- 您现在的位置：买卖IC网 > PDF目录20392 > DC1669A (Linear Technology)BOARD EVAL LTM4627 PDF资料下载
参数资料
| 型号： | DC1669A |
| 厂商： | Linear Technology |
| 文件页数： | 7/32页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL LTM4627 |
| 软件下载： | LTM4627 Spice Model |
| 设计资源： | LTM4627 Gerber Files DC1669A Design Files |
| 标准包装： | 1 |
| 系列： | LTM®, uModule® |
| 主要目的： | DC/DC，步升 |
| 输出及类型： | 1，非隔离 |
| 输出电压： | 1V，1.2V，1.5V，1.8V，2.5V，3.3V |
| 电流 - 输出： | 15A |
| 输入电压： | 4.5 ~ 20 V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 500kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | LTM4627 |
| 相关产品： | LTM4627IV#PBF-ND - IC UMODULE DC/DC 15A 133LGA LTM4627EV#PBF-ND - IC UMODULE DC/DC 15A 133LGA |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
LTM4627
PIN FUNCTIONS
V IN (A1-A6, B1-B6, C1-C6): Power Input Pins. Apply input
voltage between these pins and GND pins. Recommend
placing input decoupling capacitance directly between V IN
pins and GND pins.
V OUT (J1-J10, K1-K11, L1-L11, M1-M11): Power Output
Pins. Apply output load between these pins and GND
pins. Recommend placing output decoupling capacitance
directly between these pins and GND pins. Review Table 4.
GND (B7, B9, C7, C9, D1-D6, D8, E1-E7, E9, F1-F9, G1-G9,
H1-H9): Power Ground Pins for Both Input and Output
Returns.
PGOOD (F11, G12): Output Voltage Power Good Indicator.
Open-drain logic output that is pulled to ground when the
output voltage exceeds a ±10% regulation window. Both
pins are tied together internally.
SGND (G11, H11, H12): Signal Ground Pin. Return ground
path for all analog and low power circuitry. Tie a single
connection to the output capacitor GND in the application.
See layout guidelines in Figure 17.
MODE_PLLIN (A8): Forced Continuous Mode, Burst Mode
Operation, or Pulse-Skipping Mode Selection Pin and
External Synchronization Input to Phase Detector Pin.
Connect this pin to INTV CC to enable pulse-skipping mode
of operation. Connect to ground to enable forced continuous
mode of operation. Floating this pin will enable Burst Mode
operation. A clock on this pin will enable synchronization
with forced continuous operation. See the Applications
Information section.
f SET (B12): A resistor can be applied from this pin to
ground to set the operating frequency, or a DC voltage
can be applied to set the frequency. See the Applications
Information section.
TRACK/SS (A9): Output Voltage Tracking Pin and Soft-
Start Inputs. The pin has a 1.2μA pull-up current source.
A capacitor from this pin to ground will set a soft-start
ramp rate. In tracking, the regulator output can be tracked
to a different voltage. The different voltage is applied to
a voltage divider then the slave output’s track pin. This
voltage divider is equal to the slave output’s feedback
divider for coincidental tracking. See the Applications
Information section.
V FB (F12): The Negative Input of the Error Amplifier.
Internally, this pin is connected to V OUT_LCL with a
60.4k precision resistor. Different output voltages can
be programmed with an additional resistor between V FB
and ground pins. In PolyPhase ? operation, tying the
V FB pins together allows for parallel operation. See the
Applications Information section for details.
COMP (A11): Current Control Threshold and Error Amplifier
Compensation Point. The current comparator threshold
increases with this control voltage. Tie all COMP pins
together for parallel operation. The device is internally
compensated.
RUN: (A10) Run Control Pin. A voltage above 1.4V will turn
on the module. A 5.1V Zener diode to ground is internal
to the module for limiting the voltage on the RUN pin to
5V, and allowing a pull-up resistor to V IN for enabling the
device. Limit current into the RUN pin to ≤ 2mA.
INTV CC : (A7, D9) Internal 5V LDO for Driving the Control
Circuitry and the Power MOSFET Drivers. Both pins are
internally connected. The 5V LDO has a 100mA current limit.
EXTV CC (E12): External power input to an internal control
switch allows an external source greater than 4.7V, but
less than 6V to supply IC power and bypass the internal
INTV CC LDO. EXTV CC must be less than V IN at all times
during power-on and power-off sequences. See the Ap-
plications Information section.
4627fc
For more information www.linear.com/LTM4627
7
相关PDF资料 |
PDF描述 |
|---|---|
| IR2151S | IC DRVR HALF BRDG SELF-OSC 8SOIC |
| R0.25D-3.33.3/HP-R | CONV DC/DC 0.25W 3.3V +/-3.3VOUT |
| DC1472A | BOARD DEMO LTM4618 |
| EBM15DTKS | CONN EDGECARD 30POS DIP .156 SLD |
| IR2136S | IC DRIVER BRIDGE 3-PHASE 28-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DC1669B | 制造商:Linear Technology 功能描述:LTM4627EV Demo Board 20V, 15A DC/DC 制造商:Linear Technology 功能描述:LTM4627EV Demo Board 20V, 15A DC/DC Module Regulator |
| DC16-73 | 制造商:Skyworks Solutions Inc 功能描述:DIRECTIONAL COUPLER 15DB P/N: N011 |
| DC16-73LF | 功能描述:信号调节 .3-2.7GHz Coupling 15.6dB and 14.8dB RoHS:否 制造商:EPCOS 产品:Duplexers 频率:782 MHz, 751 MHz 频率范围: 电压额定值: 带宽: 阻抗:50 Ohms 端接类型:SMD/SMT 封装 / 箱体:2.5 mm x 2 mm 工作温度范围:- 30 C to + 85 C 封装:Reel |
| DC16-73LF-B | 制造商:Skyworks Solutions Inc 功能描述:RF DIRECTIONAL COUPLER |
| DC1676A | 制造商:Linear Technology 功能描述:BOARD DEMO LTC4359 制造商:Linear Technology 功能描述:DEMO BOARD, LTC4359, IDEAL DIODE CONTROLLER; Silicon Manufacturer:Linear Technology; Silicon Core Number:LTC4359; Kit Application Type:Power Management; Application Sub Type:Ideal Diode; Kit Contents:Demo Board LTC4359 |
发布紧急采购，3分钟左右您将得到回复。