- 您现在的位置：买卖IC网 > PDF目录9172 > DS1856B-M50+ (Maxim Integrated Products)IC DGTL POT 50K 256TAPS 16CSBGA PDF资料下载
参数资料
| 型号： | DS1856B-M50+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 19/31页 |
| 文件大小： | 0K |
| 描述： | IC DGTL POT 50K 256TAPS 16CSBGA |
| 产品培训模块： | Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 接片： | 256 |
| 电阻（欧姆）： | 50k |
| 电路数： | 2 |
| 温度系数： | 标准值 50 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | 2 线串口 |
| 电源电压： | 2.85 V ~ 5.5 V |
| 工作温度： | -40°C ~ 95°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-LBGA，CSPBGA |
| 供应商设备封装： | 16-CSBGA（4x4） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
Dual, Temperature-Controlled Resistors with Inter-
nally Calibrated Monitors and Password Protection
26
Maxim Integrated
DS1856
gain_result = gain_result + 2^n;
Force the 90% FS input (2.949075V);
Meas2 = read the digital result from
the part;
If Meas2 >= Clamp then
gain_result = gain_result – 2^n;
Else
Force the null input (0.5V);
Meas1 = read the digital result from
the part;
if (Meas2 – Meas1) > (CNT2 –
CNT1) then
gain_result = gain_result – 2^n;
end;
Set the gain register to gain_result;
The gain register is now set and the resolution of the
conversion will best match the expected LSB. The next
step is to calibrate the offset of the DS1856. With the
correct gain value written to the gain register, again
force the null input to the pin. Read the digital result
from the part (Meas1). The offset value is equal to the
negative value of Meas1.
The calculated offset is now written to the DS1856 and
the gain and offset scaling is now complete.
Right-Shifting A/D Conversion Result
(Scalable Dynamic Ranging)
The right-shifting method is used to regain some of the
lost ADC range of a calibrated system. If a system is cali-
brated so the maximum expected input results in a digi-
tal output value of less than 7FFFh (1/2 FS), then it is a
candidate for using the right-shifting method.
If the maximum desired digital output is less than 7FFFh,
then the calibrated system is using less than 1/2 of the
ADC’s range. Similarly, if the maximum desired digital
output is less than 1FFFh, then the calibrated system is
only using 1/8 of the ADC’s range. For example, if using
a zero for the right-shift during internal calibration and
the maximum expected input results in a maximum digi-
tal output less than 1FFCh, only 1/8 of the ADC’s range is
used. If left like this, the three MS bits of the ADC will
never be used. In this example, a value of 3 for the right-
shifting maximizes the ADC range. No resolution is lost
since this is a 12-bit converter that is left justified. The
value can be right-shifted four times without losing reso-
lution. Table 9 shows when the right-shifting method can
be used.
Temperature Conversion
The direct-to-digital temperature sensor measures tem-
perature through the use of an on-chip temperature
measurement technique with a -40°C to +102°C operat-
ing range. Temperature conversions are initiated upon
power-up, and the most recent conversion is stored in
memory locations 60h and 61h of the Main Device,
which are updated every tframe. Temperature conver-
sions do not occur during an active read or write to
memory.
The value of each resistor is determined by the tempera-
ture-addressed look-up table. The look-up table assigns
a unique value to each resistor for every 2°C increment
with a 1°C hysteresis at a temperature transition over the
operating temperature range (see Figure 4).
Offset
gister
Meas
_Re
=
1
4
OUTPUT RANGE USED
WITH ZERO RIGHT-SHIFTS
NUMBER OF
RIGHT-SHIFTS NEEDED
0h....FFFFh
0
0h....7FFFh
1
0h....3FFFh
2
0h....1FFFh
3
0h....0FFFh
4
Table 9. Right Shifting
M6
M5
M4
M3
M2
M1
2
4
6
8
10
12
TEMPERATURE (
°C)
MEMORY
LOCATION
INCREASING
TEMPERATURE
DECREASING
TEMPERATURE
Figure 4. Look-Up Table Hysteresis
相关PDF资料 |
PDF描述 |
|---|---|
| V72A8H300BL | CONVERTER MOD DC/DC 8V 300W |
| DS1856E-M50+ | IC DGTL POT 50K 256TAPS 16TSSOP |
| MS27466T23B2P | CONN RCPT 85POS WALL MT W/PINS |
| MS3114P18-11S | CONN RCPT 11POS JAM NUT W/SCKT |
| VE-BWP-MY-F1 | CONVERTER MOD DC/DC 13.8V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1856B-M50/T | 制造商:Maxim Integrated Products 功能描述:- Tape and Reel |
| DS1856B-M50/T&R | 制造商:Maxim Integrated Products 功能描述:DUALTEMP 50K,3MON BGA FULL A0/A2M T - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC DGTL POT 50K 2CH 16CSBGA 制造商:Maxim Integrated Products 功能描述:Digital Potentiometer ICs Extremely Acc SPI Bus RTC |
| DS1856B-M50+ | 功能描述:数字电位计 IC DUALTEMP 50K3MON W/FULL AO/A2 MEMORY RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| DS1856B-M50+R | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Dual, Temperature-Controlled Resistors with Calibrated Monitors and Password Protection |
| DS1856B-M50+T | 制造商:Maxim Integrated Products 功能描述:DUALTEMP 50K,3MON BGA W/FULL AO/A2 MEMORY - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。