- 您现在的位置：买卖IC网 > PDF目录20026 > DS1863E+ (Maxim Integrated)IC LASR CTRLR 1CHAN 5.5V 16TSSOP PDF资料下载
参数资料
| 型号： | DS1863E+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 18/62页 |
| 文件大小： | 0K |
| 描述： | IC LASR CTRLR 1CHAN 5.5V 16TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 96 |
| 类型： | 激光二极管控制器 |
| 通道数： | 1 |
| 电源电压： | 2.85 V ~ 5.5 V |
| 电流 - 电源： | 5mA |
| 电流 - 偏置： | 1.2mA |
| 工作温度： | -40°C ~ 95°C |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
| 产品目录页面： | 1429 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页
Burst-Mode PON Controller
With Integrated Monitoring
Acknowledge Polling: Any time an EEPROM location
MSB
LSB
is written, the DS1863 requires the EEPROM write time
1
0
1
0
0
0
1
R/W
(t W ) after the STOP condition to write the contents of
the byte of data to EEPROM. During the EEPROM write
SLAVE
ADDRESS*
READ/WRITE
BIT
time, the device will not acknowledge its slave address
because it is busy. It is possible to take advantage of
that phenomenon by repeatedly addressing the
THE DEFAULT SLAVE ADDRESS IS SHOWN, HOWEVER IT CAN BE CHANGED
USING THE DEVICE ADDRESS BYTE (TABLE 02h, BYTE 8Ch)., AND ASEL BIT.
Figure 10. DS1863 Slave Address Byte (Default)
I 2 C Communication
Writing a Single Byte to a Slave: The master must
generate a START condition, write the slave address
byte (R/ W = 0), write the byte of data, and generate a
STOP condition. The master must read the slave ’ s
acknowledgement during all byte write operations.
Writing Multiple Bytes to a Slave: To write multiple
bytes to a slave, the master generates a start condition,
writes the slave address byte (R/ W = 0), writes the
memory address, writes up to 8 data bytes, and gener-
ates a stop condition. The DS1863 writes 1 to 8 bytes (1
page or row) with a single write transaction. This is
internally controlled by an address counter that allows
data to be written to consecutive addresses without
transmitting a memory address before each data byte is
sent. The address counter limits the write to one 8-byte
page (one row of the memory map). Attempts to write to
additional pages of memory without sending a stop
condition between pages results in the address counter
wrapping around to the beginning of the present row.
Example: A 3-byte write starts at address 06h and
writes three data bytes (11h, 22h, and 33h) to three
“ consecutive ” addresses. The result is that addresses
06h and 07h would contain 11h and 22h, respectively,
and the third data byte, 33h, would be written to
address 00h.
To prevent address wrapping from occurring, the mas-
ter must send a stop condition at the end of the page,
then wait for the bus-free or EEPROM-write time to
elapse. Then the master can generate a new start con-
dition, and write the slave address byte (R/ W = 0) and
the first memory address of the next memory row
before continuing to write data.
DS1863, which allows the next page to be written as
soon as the DS1863 is ready to receive the data. The
alternative to acknowledge polling is to wait for a maxi-
mum period of t W to elapse before attempting to write
again to the device.
EEPROM Write Cycles: When EEPROM writes occur to
the memory, the DS1863 will write to all three EEPROM
memory locations, even if only a single byte was modi-
fied. Because all three bytes are written, the bytes that
were not modified during the write transaction are still
subject to a write cycle. This can result in all three bytes
being worn out over time by writing a single byte repeat-
edly. The DS1863 ’ s EEPROM write cycles are specified in
the NV Memory Characteristics table. The specification
shown is at the worst-case temperature. If zero-crossing
detection is enabled, EEPROM write cycles cannot begin
until after the zero-crossing detection is complete.
Reading a Single Byte from a Slave: To read a single
byte from the slave, the master generates a START con-
dition, writes the slave address byte with R/ W = 1, reads
the data byte with a NACK to indicate the end of the
transfer, and generates a STOP condition. When a single
byte is read, it will always be the Potentiometer 0 value.
Reading Multiple Bytes from a Slave: The read oper-
ation can be used to read multiple bytes with a single
transfer. When reading bytes from the slave, the master
simply ACKs the data byte if it desires to read another
byte before terminating the transaction. After the mas-
ter reads the last byte, it NACKs to indicate the end of
the transfer and generates a STOP condition. The first
byte read will be the Potentiometer 0 Wiper Setting. The
next byte will be the Potentiometer 1 Wiper Setting. The
third byte is the Configuration Register byte. If an ACK
is issued by the master following the Configuration
Register byte, then the DS1863 will send the
Potentiometer 0 Wiper Setting again. This round robin
reading will occur as long as each byte read is followed
by an ACK from the master.
18
____________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| TCJP476M006R0500 | CAP TANT 47UF 6.3V 20% 0805 |
| VI-20P-CX | CONVERTER MOD DC/DC 13.8V 75W |
| ECM12DTBH | CONN EDGECARD 24POS R/A .156 SLD |
| 5749111-4 | CONN 50POS .050 CHAMPPLUG SCHCVR |
| TPSD157M010R0050 | CAP TANT 150UF 10V 20% 2917 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1863E+ | 功能描述:激光驱动器 Burst-Mode PON Ctlr w/Integrated Mntr RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| DS1863E+R | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Burst-Mode PON Controller With Integrated Monitoring |
| DS1863E+T | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Burst-Mode PON Controller With Integrated Monitoring |
| DS1863E+T&R | 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:BURST CNTRLR 16TSSOP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC LASR CTRLR 1CHAN 5.5V 16TSSOP |
| DS1863E+T&R | 功能描述:激光驱动器 Burst-Mode PON Ctlr w/Integrated Mntr RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。