- 您现在的位置：买卖IC网 > PDF目录20027 > DS1864T+ (Maxim Integrated)IC LASER CTRLR 1CHAN 5.5V 28TQFN PDF资料下载
参数资料
| 型号： | DS1864T+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 17/72页 |
| 文件大小： | 0K |
| 描述： | IC LASER CTRLR 1CHAN 5.5V 28TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 60 |
| 类型： | 激光二极管控制器（光纤） |
| 通道数： | 1 |
| 电源电压： | 2.97 V ~ 5.5 V |
| 电流 - 电源： | 3mA |
| 工作温度： | -40°C ~ 95°C |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 供应商设备封装： | 28-TQFN-EP（5x5） |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页
SFP Laser Controller and
Diagnostic IC
Table 1. LUT Addresses For
Corresponding Temperature Values
Digital Diagnostics
In optical transceiver applications, the external monitor
channels are typically used for Bias Current (IBI)
ADDRESS (hex)
80
81
82
?
C6
C7
CORRESPONDING
TEMPERATURE (°C)
≤ -40°C
-38°C
-36°C
?
+100°C
≥ +102°C
through pins MON1P and MON1N, Transmitted Power
(TXP) through a MON2 pin, and Received Power (RIN)
through pins MON3P and MON3N. While MON2 is a
single-ended monitor, MON1 and 3 have the option of
being used as differential or single-ended monitors. To
use these channels single-ended, connect the ‘N’ side
to ground. A 13-bit ADC samples and digitizes the five
analog signals and the results are stored in registers
60h through 69h in the Lower Memory. The representa-
tive digital values are 13-bits wide (left justified), and
current temperature. The DAC value referenced in the
LUT is then loaded into address 82h of Table 04h
(Table 01h in DS1859 configuration) for DAC0 and into
address 83h of Table 04h (Table 01h in DS1859 config-
uration) for DAC1.
DAC Manual Mode
During normal operation, the DAC setting is automati-
cally modified once per conversion cycle based on the
ADC results. However, if the TEN bit (bit 1, address
80h, Table 04h (Table 01h in DS1859 configuration)) is
set to 0, the DACs are placed in a manual mode and
temperature indexing is disabled. Once in manual
mode, the user programs the current-sink DACs by
writing the desired positions to addresses 82h and 83h
in Table 04h (Table 01h in DS1859 configuration) to
control DAC0 and DAC1, respectively.
RSEL Operation
The rate select pin (RSEL) along with the SELC rate
select bit (Lower Memory Register, byte 6Eh, bit 3)
determine the state of the RSELOUT pin, which is
intended to be used to control receiver multirate perfor-
mance. The RSEL pin state is OR’ed with the state of the
SELC bit to determine the RSELOUT pin state. Bit SELS
(Lower Memory Register, byte 6Eh, bit 4) indicates the
state of the RSEL pin. See Figure 13 for more details.
Monitoring Features
The DS1864 incorporates five basic monitor channels,
which include temperature, supply voltage (V CC ), and
three external channels (MON1, MON2, and MON3).
These analog signals are sampled and converted into
digital measurements and compared to threshold limits
to determine alarm and warning signals and fault states.
These five signals can be calibrated externally, using
reserved registers for calibration values, or internally,
using built-in gain, offset, and right-shifting functions.
are stored in successive register pairs. The tempera-
ture value is stored in a 2’s complement format, while
V CC and the three analog inputs are stored in an un-
signed format. The digital values are updated every
t FRAME . From these measurements, alarms and warn-
ings are generated after a digital comparison with high
and low set limits. A maskable interrupt, MINT, asserted
through TX-Fault, can be enabled based on any combi-
nation of alarms and warnings.
Alarm and Warning Flags
Alarm and warning flags are generated by comparing
the digitally converted values of the measured tempera-
ture, supply voltage, and three MON inputs with user-
programmed upper and lower limits. These limits are
stored in EEPROM locations 00h through 27h in the
Lower Memory. The two types of flags, alarm and warn-
ing, are also stored in the Lower Memory. Addresses
70h and 71h contain the alarm flags, while addresses
74h and 75h contain the warning flags. The Alarms and
Warnings section under Fault Management describe
how to program the alarm and warning thresholds, and
how to use them to generate interrupts.
Calibration Overview
Calibration is provided internally or externally. External
calibration makes use of a range of registers, reserved
for this purpose according to SFF-8472 standard. This
range is 38h to 5F in the Lower Memory Registers. The
calibration constants are loaded in the registers during
system test. In external calibration mode, a host
processor retrieves the constants and computes the
calibrated data.
The DS1864 features internal calibration for the five
analog channels. Internal calibration makes use of two
registers for four of the five monitored analog channels:
V CC , MON1 (Bias Current (IBI)), MON2 (Transmitted
Power (TXP)) and MON3 (Received Power (RIN)). One
register is for offset calibration, the other for gain cali-
bration. Both registers are loaded during system test.
Only the offset scaling register is used for temperature.
____________________________________________________________________
17
相关PDF资料 |
PDF描述 |
|---|---|
| R2S-153.3/HP | CONV DC/DC 2W 15VIN 3.3VOUT |
| NCV8664ST33T3G | IC REG LDO 3.3V .15A SOT-223 |
| VI-B5P-CV-S | CONVERTER MOD DC/DC 13.8V 150W |
| HMC26DRXI-S734 | CONN EDGECARD 52POS DIP .100 SLD |
| VI-B52-CV-S | CONVERTER MOD DC/DC 15V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1864T+ | 功能描述:激光驱动器 SFP Laser Controller & Diagnostic IC RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| DS1864T+T&R | 制造商:Maxim Integrated Products 功能描述:DUAL TMP CTRL DAC+MON QFN T&R LF - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC LASER CTRLR 1CHAN 5.5V 28TQFN |
| DS1864T+T&R | 功能描述:激光驱动器 SFP Laser Controller & Diagnostic IC RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| DS1865 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:PON Triplexer Control and Monitoring Circuit |
| DS1865_09 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:PON Triplexer Control and Monitoring Circuit |
发布紧急采购，3分钟左右您将得到回复。