- 您现在的位置：买卖IC网 > PDF目录20027 > DS1864T+ (Maxim Integrated)IC LASER CTRLR 1CHAN 5.5V 28TQFN PDF资料下载
参数资料
| 型号： | DS1864T+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 23/72页 |
| 文件大小： | 0K |
| 描述： | IC LASER CTRLR 1CHAN 5.5V 28TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 60 |
| 类型： | 激光二极管控制器（光纤） |
| 通道数： | 1 |
| 电源电压： | 2.97 V ~ 5.5 V |
| 电流 - 电源： | 3mA |
| 工作温度： | -40°C ~ 95°C |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 供应商设备封装： | 28-TQFN-EP（5x5） |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页
SFP Laser Controller and
Diagnostic IC
and TX-F is set active. A falling edge of transmit disable
(the logic OR of TX-D/TXDC) will initiate a safety fault
recovery. At this point, the FETG output and the DACs
are enabled. The TX-F output will not be disabled until a
t INITR1 time later. LTXP is masked during this time peri-
od to allow for system recovery. HBAL and HTXP flags
are not masked and will generate another safety fault
if their appropriate limit is exceeded. A safety fault is not
generated on standard shutdowns (the logic OR of
TX-D/TXDC).
Power-Up and Low-Voltage Operation
During power-up, the device is inactive until V CC
exceeds the analog power-on-reset (V POA ), at which
time the device becomes fully functional. Once V CC
exceeds V POA , the RDYB bit (address byte 6Eh, bit 0)
is timed to go from a 1 to a 0 and indicates when A/D
conversions begin. If V CC ever dips below V POA , the
RDYB bit reads as a 1 again. Once a device exceeds
V POA and the EEPROM is recalled, the values remain
active (recalled) until V CC falls below V POD .
As the device powers up, the V CC low alarm flag
defaults to a 1 until the first V CC A/D conversion occurs
and sets or clears the flag accordingly.
Memory Organization
The DS1864 memory map is divided into seven sec-
tions that include Auxiliary Memory, Lower Memory,
and five Upper Memory tables. The Upper Memory
tables are addressed by setting the Table Select Byte
(7Fh in the Lower Memory) to the desired table number
and accessing the upper memory locations (80h to
FFh). The Lower Memory and Auxiliary Device can be
addressed at any time regardless of the state of the
Table Select Byte. The Lower Memory and Table 04h
(Table 01h in DS1859 configuration) are used to config-
ure the DS1864 and read the status of the monitors.
Memory Tables 02h and 03h contain the temperature
indexed DAC Lookup Tables. Memory Tables 05h and
01h (Table 00h in DS1859 configuration) contain masks
for alarm and warning flags. Table 01h (Table 00h in
DS1859 configuration) also contains password settings.
The Mode bit (bit 3, byte 89h in Table 04h (Table 01h in
DS1859 configuration)) selects between DS1852/
DS1856-compatible memory configuration or the
DS1859-compatible memory configuration. See Figures
16 and 17 for more information.
Die Identification
DS1864 has an ID hard coded in its die. Three registers
(Table 05h, bytes C0h to C2h) are assigned for this fea-
ture. Two registers are for the device ID, and a third
register is for the version number. ID registers are hard-
wired at the time of manufacture and are globally read-
able through the I 2 C interface.
Memory Map Configurations
The default DS1864 memory configuration is compati-
ble with the DS1852 memory map. The Mode bit (bit 3,
register 89h of Table 04h (Table 01h in DS1859 config-
uration)) can be selected to make the DS1864 memory
map compatible with the DS1859 memory map. Figure
16 shows the DS1852/DS1856 compatible configuration
(default), and Figure 17 shows the DS1859-compatible
configuration.
When the DS1864 is in the DS1852-compatible configu-
ration, user memory is in Table 01h. In contrast, when
the DS1864 is in the DS1859-compatible configuration
(having set Mode to 1), user memory is in Table 00h. In
addition, Table 04h in the DS1852 configuration will be
reassigned as Table 01h in the DS1859 configuration.
Memory Protection and Passwords
The memory of the DS1864 is protected by two pass-
words, PW1 (user password) and a PW2 (vendor pass-
word). The password entry location for both passwords
is in 7Bh-7Eh of Lower Memory and resides in SRAM.
The PW2 password setting locations are in Table 04h
(Table 01h in DS1859 configuration), registers C1h to
C6h. The PW1 password settings are in Table 05h, reg-
isters D1h to D6h. Password setting and password
entry bytes are write only (read as 0s).
Furthermore, the Auxiliary Memory and Main Device
Memory are divided into eight blocks; see Table 9. The
read and write protection for each block is activated by
an enable bit. Two sets of enable bytes are used for
both PW1 and PW2 level access, one byte to allow read
access to the memory blocks and one byte for write
access to the memory blocks. The two PW2 password
enable bytes are located in Table 04h (Table 01h in
DS1859 configuration), registers C1h and C2h. The
PW1 password enable bytes are located in Table 05h,
registers D1h and D2h. Table 8 shows how the pass-
word enable bytes can be configured to protect the
memory blocks. Table 9 shows the bit assignments for
each of the eight blocks of DS1864 memory. See the
registers mentioned above in the Memory Map section
for more details.
Note that regardless of read/write permissions for a
given table, password settings and password entry are
unconditionally read protected. They are write protect-
ed if the proper write enable bit is set to 1. Bytes 78h to
7Fh in Lower Memory are unprotected.
____________________________________________________________________
23
相关PDF资料 |
PDF描述 |
|---|---|
| R2S-153.3/HP | CONV DC/DC 2W 15VIN 3.3VOUT |
| NCV8664ST33T3G | IC REG LDO 3.3V .15A SOT-223 |
| VI-B5P-CV-S | CONVERTER MOD DC/DC 13.8V 150W |
| HMC26DRXI-S734 | CONN EDGECARD 52POS DIP .100 SLD |
| VI-B52-CV-S | CONVERTER MOD DC/DC 15V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1864T+ | 功能描述:激光驱动器 SFP Laser Controller & Diagnostic IC RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| DS1864T+T&R | 制造商:Maxim Integrated Products 功能描述:DUAL TMP CTRL DAC+MON QFN T&R LF - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC LASER CTRLR 1CHAN 5.5V 28TQFN |
| DS1864T+T&R | 功能描述:激光驱动器 SFP Laser Controller & Diagnostic IC RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| DS1865 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:PON Triplexer Control and Monitoring Circuit |
| DS1865_09 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:PON Triplexer Control and Monitoring Circuit |
发布紧急采购，3分钟左右您将得到回复。