- 您现在的位置：买卖IC网 > PDF目录1913 > DS1865T+ (Maxim Integrated Products)IC PON TRIPLEXER CTRLR 28TQFN-EP PDF资料下载
参数资料
| 型号： | DS1865T+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 3/67页 |
| 文件大小： | 0K |
| 描述： | IC PON TRIPLEXER CTRLR 28TQFN-EP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 系列： | * |
| 类型： | * |
| 应用： | * |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 供应商设备封装： | 28-TQFN-EP（5x5） |
| 包装： | 管件 |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页
DS1865
PON Triplexer Control and
Monitoring Circuit
____________________________________________________________________
11
The APC loop’s feedback is the monitor diode (BMD)
current, which is converted to a voltage using an exter-
nal resistor. The feedback voltage is compared to an 8-
bit scaleable voltage reference that determines the
APC set point of the system. Scaling of the reference
voltage accommodates the wide range in photodiode
sensitivities. This allows the application to take full
advantage of the APC reference’s resolution.
The DS1865 has an LUT to allow the APC set point to
change as a function of temperature to compensate for
tracking error (TE). The TE LUT (Table 05h) has 36
entries that determine the APC setting in 4°C windows
between -40°C to +100°C. Ranging of the APC DAC is
possible by programming a single byte in Table 02h.
Modulation Control
The MOD output is an 8-bit scaleable voltage output that
interfaces with the MAX3643’s VMSET input. An external
resistor to ground from the MAX3643’s MODSET pin sets
the maximum current the voltage at VMSET input can
produce for a given output range. This resistor value
should be chosen to produce the maximum modulation
current the laser type requires over temperature. Then
the MOD output’s scaling is used to calibrate the full-
scale (FS) modulation output to a particular laser’s
requirements. This allows the application to take full
advantage of the MOD output’s resolution. The modula-
tion LUT can be programmed in 2°C increments over the
-40°C to +102°C range.
Ranging of the MOD DAC is possible by programming
a single byte in Table 02h.
BIAS and MOD Output
During Power-Up
On power-up, the modulation and bias outputs remain
off until VCC is above VPOA and a temperature conver-
sion has been completed. If the VCC LO ADC alarm is
enabled, then a VCC conversion above the customer-
defined VCC low alarm level is required before the
outputs are enabled with the value determined by the
temperature conversion and the modulation LUT.
When the MOD output is enabled and BEN is high, the
BIAS output is turned on to a value equal to ISTEP (see
Figure 1). The startup algorithm checks if this bias cur-
rent causes a feedback voltage above the APC set point,
and if it does not it continues increasing the BIAS by
ISTEP until the APC set point is exceeded. When the APC
set point is exceeded, the DS1865 begins a binary
search to quickly reach the bias current corresponding
to the proper power level. After the binary search is com-
pleted the APC integrator is enabled, and single LSB
steps are taken to tightly control the average power.
All quick-trip alarm flags are masked until the binary
search is completed. However, the BIAS MAX alarm is
monitored during this time to prevent the bias output
from exceeding MAX IBIAS. During the bias current ini-
tialization, the bias current is not allowed to exceed
MAX IBIAS. If this occurs during the ISTEP sequence,
the binary search routine begins. If MAX IBIAS is
exceeded during the binary search, the next smaller
step is activated. ISTEP or binary increments that would
cause IBIAS to exceed MAX IBIAS are not taken.
Masking the alarms until the completion of the binary
search prevents false trips during startup.
ISTEP is programmed by the customer using the Startup
Step register. This value should be programmed to the
maximum safe current increase that is allowable during
startup. If this value is programmed too low, the DS1865
will still operate, but it could take significantly longer for
the algorithm to converge and hence to control the aver-
age power.
If a fault is detected and TX-D is toggled to re-enable the
outputs, the DS1865 powers up following a similar
sequence to an initial power-up. The only difference is
that the DS1865 already has determined the present tem-
perature, so the tINIT time is not required for the DS1865
to recall the APC and MOD set points from EEPROM.
If the Bias-En bit (Table 02h, Register 80h) is written to
0, the BIAS DAC is manually controlled by the MAN
IBIAS register (Table 02h, Registers F8h–F9h).
BIAS and MOD Output as a Function
of Transmit Disable (TX-D)
If the TX-D pin is asserted (logic 1) during normal oper-
ation, the outputs are disabled within tOFF. When TX-D
is deasserted (logic 0), the DS1865 turns on the MOD
output with the value associated with the present tem-
perature, and initializes the BIAS using the same
search algorithm used at startup. When asserted, the
soft TX-D (Lower Memory, Register 6Eh) offers a soft-
ware control identical to the TX-D pin (see Figure 2).
APC and Quick-Trip Shared
Comparator Timing
As shown in Figure 3, the DS1865’s input comparator is
shared between the APC control loop and the three
quick-trip alarms (TXP-HI, TXP-LO, and BIAS HI). The
comparator polls the alarms in a round-robin multi-
plexed sequence. Six of every eight comparator read-
ings are used for APC loop-bias current control. The
other two updates are used to check the HTXP/LTXP
(monitor diode voltage) and the HBIAS (MON1) signals
against the internal APC and BIAS reference. The
HTXP/LTXP comparison checks HTXP to see if the last
相关PDF资料 |
PDF描述 |
|---|---|
| DS1866Z/T&R | IC POT TRIM LOG 2.7-5.5V 8-SOIC |
| DS1867S-010+T&R | IC POT W/EEPROM DUAL 10K 16-SOIC |
| DS1868E-010/T&R | IC POT DIGITAL DUAL 10K 20-TSSOP |
| DS1869S-C10+T&R | IC RHEOSTAT DALLAST 8SOIC |
| DS1875T+T&R | IC SFP CTRLR/TRIPLEXER 38-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1865T TR | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:PON Triplexer Control and Monitoring Circuit |
| DS1865T+ | 功能描述:电流和电力监控器、调节器 PON Triplexer Cntrl & Monitoring Circuit RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| DS1865T+T&R | 制造商:Maxim Integrated Products 功能描述:TRIPLEXER CONTROL AND MONITORING CIRCUIT 1TX 1RX 1.25GBPS 28 - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC PON CONTROL TRI 28-TQFN 制造商:Maxim Integrated Products 功能描述:Current & Power Monitors & Regulators PON Triplexer Cntrl & Monitoring Circuit |
| DS1865T+T&R | 功能描述:电流和电力监控器、调节器 PON Triplexer Cntrl & Monitoring Circuit RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| DS1865T+TR | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:PON Triplexer Control and Monitoring Circuit |
发布紧急采购，3分钟左右您将得到回复。