参数资料
| 型号： | DS2149QN+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/32页 |
| 文件大小： | 0K |
| 描述： | IC LIU T1/J1 5V 28-PLCC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 37 |
| 类型： | 线路接口装置（LIU） |
| 规程： | T1/J1 |
| 电源电压： | 4.75 V ~ 5.25 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-LCC（J 形引线） |
| 供应商设备封装： | 28-PLCC（11.51x11.51） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
DS2149
15 of 32
5. TRANSMITTER
5.1 Transmit Digital Data Interface
Data is clocked into the device at the TCLK rate. In bipolar mode, TPOS and TNEG are the data inputs;
in NRZ mode, TDATA is the data input. Input data can pass through either the jitter attenuator or the
B8ZS encoder or both. In software mode, setting ENCENB enables B8ZS encoding. In hardware mode,
floating the MODE1 pin enables B8ZS encoding. With B8ZS encoding enabled, the L0 through L3 inputs
determine the coding and is listed in Table 4-E. TCLK supplies input synchronization. See Section 12 for
the TCLK and MCLK timing requirements.
5.2 Transmit Monitoring
In software mode, the DFMO bit in the status register is set when an open circuit in the transmitter path is
detected. A transition on this bit can provide an interrupt, and a transition sets the DFMO bit in the
transition status register. Setting CDFMO in the interrupt mask register, leaving a 1 in that bit location
masks the interrupt.
5.3 Transmit Idle Mode
Transmit idle mode allows multiple transceivers to be connected to a single line for redundant
applications. When TCLK is not present, transmit idle mode becomes active, and TTIP and TRING
change to high-impedance state. Remote loopback, dual loopback, TAIS, or detection of network loop-up
code in the receive direction temporarily disable the high-impedance state.
5.4 Transmit Pulse Shape
As shown in Table 4-E, line build-out control inputs (L0 through L3) determine the transmit pulse shape.
In software mode, these control inputs are located in control register 1; in hardware mode, these control
inputs are the L0 through L3 pins.
Shaped pulses meeting the various T1, DS1, and DSX-1 specifications are applied to the AMI line driver
for transmission onto the line at TTIP and TRING. The transceiver produces DSX-1 pulses for short-haul
T1 applications (settings from 0dB to 6dB of cable) and DS1 pulses for long-haul T1 applications
(settings from 0dB to -22.5dB). Refer to Table 4-E for pulse mask specifications.
6. RECEIVER
A 1:1 transformer provides the interface between the twisted pair and receiver inputs RTIP and RRING.
Recovered data is output at RPOS and RNEG (or RDATA in NRZ mode), and the recovered clock is
output at RCLK. See Section 12 for receiver timing specifications.
6.1 Receive Equalizer
The receiver can apply up to 36dB of gain. Control of the equalizer is accomplished by the L0 through L3
control inputs. These control signals are detailed in Table 4-E and determine the maximum gain that is
applied. In software mode, these control signals are in Control Register 1; in hardware mode, these
control inputs are the L0 through L3 pins. With L0 low, up to 36dB of gain can be applied; when L0 is
high, 26dB can be applied in the gain limit to provide better noise immunity in shorter loop operations.
6.2 Receive Data Recovery
The clock and data recovery engine provides input jitter tolerance that exceeds the requirements of AT&T
62411. Inbound signal is filtered, equalized, and over-sampled 16 times. Then it is applied to the B8ZS
decoder if enabled.
相关PDF资料 |
PDF描述 |
|---|---|
| DS21348GN | IC LIU LN T1/E1/J1 3.3V 49-BGA |
| VI-241-MX-F3 | CONVERTER MOD DC/DC 12V 75W |
| MAX214EPI+ | IC TXRX RS-232 PROG 28-DIP |
| MAX214EWI+ | IC TXRX RS-232 PROG 28-SOIC |
| HI5767/2IA | CONV A/D 10BIT 20MSPS 28-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2149QN/T&R | 制造商:Maxim Integrated Products 功能描述:IC LINE INTERFACE 5V T1/J1 PLCC 制造商:Maxim Integrated Products 功能描述:Network Controller & Processor ICs 5V T1/J1 Line Interface |
| DS2149QN/T&R+ | 制造商:Maxim Integrated Products 功能描述:FRAMER J1/T1 5V 28PLCC - Tape and Reel |
| DS2149QN/T&R | 功能描述:网络控制器与处理器 IC 5V T1/J1 Line Interface RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS2149QN+ | 功能描述:网络控制器与处理器 IC 5V T1/J1 Line Interface RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS2149QN+T&R | 制造商:Maxim Integrated Products 功能描述:FRAMER J1/T1 5V 28PLCC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:MXMDS2149QN+T&R 5V T1/J1 LIU T&R IND PLC 制造商:Maxim Integrated Products 功能描述:IC LIU T1/J1 5V 28-PLCC 制造商:Maxim Integrated Products 功能描述:Network Controller & Processor ICs 5V T1/J1 Line Interface |
发布紧急采购，3分钟左右您将得到回复。