参数资料
| 型号： | DS2149QN+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 8/32页 |
| 文件大小： | 0K |
| 描述： | IC LIU T1/J1 5V 28-PLCC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 37 |
| 类型： | 线路接口装置（LIU） |
| 规程： | T1/J1 |
| 电源电压： | 4.75 V ~ 5.25 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-LCC（J 形引线） |
| 供应商设备封装： | 28-PLCC（11.51x11.51） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
DS2149
16 of 32
6.3 Receive Digital-Data Interface
Recovered data is routed to the RCL monitor. In software mode, data also goes through the alarm
indication signal (AIS) monitor. The jitter attenuator can be enabled or disabled in the receive path or
transmit path. Received data can be routed to the B8ZS decoder or bypassed. Finally, the device can send
the digital data to the framer as either bipolar or NRZ data.
6.4 Receive Monitor Mode
The receive equalizer can be used in monitor-mode applications. Monitor-mode applications require
20dB of resistive attenuation of the signal, plus an allowance for cable attenuation (less than 20dB). In
software mode, setting CR3.4 (EQZMON20) enables the device to operate in monitor-mode applications
that require 20dB of resistive attenuation of the signal. Setting CR3.3 (EQZMON26) enables the device
to operate in monitor-mode applications that require 26dB of resistve attenuation. Setting both CR3.3 and
CR3.4 enables the device to operate in monitor-mode applications that require 32dB of resistive
attenuation. The monitor mode feature is not available in hardware mode.
7. JITTER ATTENUATION
The jitter attenuator only requires a jitter-free clock at 1.544MHz applied to the MCLK input. In
hardware mode, the jitter attenuator is a 32-bit FIFO buffer. Pulling the JASEL pin high places the jitter
attenuator in the receive path. Pulling the JASEL pin low places the jitter attenuator in the transmit path,
floating the JASEL pin disables the jitter attenuator. In software mode, clearing CR1.6 (JASEL0) disables
the jitter attenuator, setting CR1.6 enables the jitter attenuator. If enabled, clearing CR1.7 (JASEL1)
places the jitter attenuator in the transmit path, setting CR1.7 places the jitter attenuator in the receive
path. The jitter attenuator FIFO is 32 bits in length if CR3.2 (JA128) is cleared, 128 bits if set. The device
clocks data in the jitter attenuator using TCLK if placed in the transmit path, and RCLK if placed in the
receive path. Data is clocked out of the jitter attenuator using the dejittered clock produced by the internal
PLL. When the jitter attenuator is within two bits of overflowing or underflowing, the jitter attenuator
will adjust the output clock by one-eighth of a clock cycle. The jitter attenuator adds an average delay of
16 bits if the buffer depth is 32 bits in length, 64 bits if the buffer depth is 128 bits in length. In the event
of an RCL condition, if the jitter attenuator is in the receive path then RCLK is derived from MCLK.
Transition Status register bit TSR.6 (JALT) indicates that the jitter attenuator has adjusted the output
clock. This bit is latched, when set it remains set until the software reads the bit. The JALT can also
produce a hardware interrupt.
8. HARDWARE MODE
The DS2149 operates in hardware mode when the MODE1 pin is pulled low or floated. In hardware
mode, configuration of the device is under control of various input pins. RPOS, RNEG, and RDATA are
valid on the rising edge of RCLK only. Some functions such as INT, clock edge select, and some
diagnostic modes are not available.
相关PDF资料 |
PDF描述 |
|---|---|
| DS21348GN | IC LIU LN T1/E1/J1 3.3V 49-BGA |
| VI-241-MX-F3 | CONVERTER MOD DC/DC 12V 75W |
| MAX214EPI+ | IC TXRX RS-232 PROG 28-DIP |
| MAX214EWI+ | IC TXRX RS-232 PROG 28-SOIC |
| HI5767/2IA | CONV A/D 10BIT 20MSPS 28-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2149QN/T&R | 制造商:Maxim Integrated Products 功能描述:IC LINE INTERFACE 5V T1/J1 PLCC 制造商:Maxim Integrated Products 功能描述:Network Controller & Processor ICs 5V T1/J1 Line Interface |
| DS2149QN/T&R+ | 制造商:Maxim Integrated Products 功能描述:FRAMER J1/T1 5V 28PLCC - Tape and Reel |
| DS2149QN/T&R | 功能描述:网络控制器与处理器 IC 5V T1/J1 Line Interface RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS2149QN+ | 功能描述:网络控制器与处理器 IC 5V T1/J1 Line Interface RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS2149QN+T&R | 制造商:Maxim Integrated Products 功能描述:FRAMER J1/T1 5V 28PLCC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:MXMDS2149QN+T&R 5V T1/J1 LIU T&R IND PLC 制造商:Maxim Integrated Products 功能描述:IC LIU T1/J1 5V 28-PLCC 制造商:Maxim Integrated Products 功能描述:Network Controller & Processor ICs 5V T1/J1 Line Interface |
发布紧急采购，3分钟左右您将得到回复。