参数资料
型号: DS2438Z+T&R
厂商: Maxim Integrated Products
文件页数: 5/29页
文件大小: 0K
描述: IC MONITOR SMART BATTERY 8-SOIC
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 2,500
功能: 燃料,电量检测计/监控器
电池化学: 智能电池
电源电压: 2.4 V ~ 10 V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 8-SOIC(0.154",3.90mm 宽)
供应商设备封装: 8-SOIC
包装: 带卷 (TR)
DS2438
VOLTAGE REGISTER FORMAT Table 2
2 7
2 6
2 5
2 4
2 3
2 2
2 1
2 0
LSB
MSb
(unit = 10 mV)
LSb
0
0
0
0
0
0
2 9
2 8
MSB
BATTERY
VOLTAGE
0.05V
2.7V
3.6V
5V
7.2V
9.99V
10V
DIGITAL OUTPUT (Binary)
0000 0000 0000 0101
0000 0001 0000 1110
0000 0001 0110 1000
0000 0001 1111 0100
0000 0010 1101 0000
0000 0011 1110 0111
0000 0011 1110 1000
DIGITAL OUTPUT (Hex)
0005h
010Eh
0168h
01F4h
02D0h
03E7h
03E8H
For applications requiring a general purpose voltage A/D converter, the DS2438 can be configured so that
the result of a Convert V command will place the scaled binary representation of the voltage on the V AD
input (as opposed to the V DD input) into the Voltage Register in the same format described in Table 2.
Depending upon the state of the Status/Configuration Register, either (but not both) the V DD or V AD
voltage will be stored in the Voltage Register upon receipt of the Convert V command. Refer to the
description of the Status/Configuration Register in the Memory Map section for details. If the V AD input
is used as the voltage input, the A/D will be accurate for 1.5V < V AD < 2V DD over the range 2.4V < V DD <
5.0V. This feature gives the user the ability to have a voltage A/D that meets spec accuracy for inputs
over the entire range of 1.5V < V AD < 10V for V DD = 5.0V.
OPERATION - MEASURING BATTERY CURRENT
The DS2438 features an A/D converter that effectively measures the current flow into and out of the
battery pack by measuring the voltage across an external sense resistor. It does so in the background at a
rate of 36.41 measurements/sec; thus, no command is required to initiate current flow measurements.
However, the DS2438 will only perform current A/D measurements if the IAD bit is set to “1” in the
Status/Configuration Register. The DS2438 measures current flow in and out of the battery through the
V SENS pins; the voltage from the V SENS+ pin to the V SENS- pin is considered to be the voltage across the
current sense resistor, R SENS . The V SENS+ terminal may be tied directly to the R SENS resistor, however, for
V SENS- , we recommend use of an RC low pass filter between it and the GND end of R SENS (see the block
diagram in Figure 1). Using a 100 k W (min) resistor (R F ) and a 0.1 m F tantalum capacitor (C F ), the filter
cutoff is approximately 15.9 Hz. The current A/D measures at a rate of 36.41 times per second, or once
every 27.46 ms. This filter will capture the effect of most current spikes, and will thus allow the current
accumulators to accurately reflect the total charge which has gone into or out of the battery.
The voltage across current sense resistor R SENS is measured by the ADC and the result is placed in the
Current Register in two’s complement format. The sign (S) of the result, indicating charge or discharge,
resides in the most significant bit of the Current Register, as shown in Table 3. See “Memory Map” in
Figure 7 for the Current Register address location.
5 of 29
相关PDF资料
PDF描述
DS2703U+ IC BATT AUTHENTICATE SHA-1 8UMAX
DS2705U+ IC AUTHENTICATE SHA-1 8-UMAX
DS2710G+ IC NIMH CHRGR SGL-CELL 10-TDFN
DS2712Z+T&R IC NIMH CHARGER 16SOIC
DS2714E+ IC NIMH CHARGER QUAD 20TSSOP
相关代理商/技术参数
参数描述
DS244 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Octal Buffer/Line Driver with 3-State Outputs
DS2441 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:1-Cell Li-Ion Battery Manager
DS2442 制造商:未知厂家 制造商全称:未知厂家 功能描述:Battery Management
DS245 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Octal Bus Transceiver
DS2450 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:1-Wire Quad A/D Converter