- 您现在的位置：买卖IC网 > PDF目录1788 > DS2438Z+T&R (Maxim Integrated Products)IC MONITOR SMART BATTERY 8-SOIC PDF资料下载
参数资料
| 型号： | DS2438Z+T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 6/29页 |
| 文件大小： | 0K |
| 描述： | IC MONITOR SMART BATTERY 8-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 燃料，电量检测计/监控器 |
| 电池化学： | 智能电池 |
| 电源电压： | 2.4 V ~ 10 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
DS2438
CURRENT REGISTER FORMAT Table 3
(This register actually stores the voltage measured across current sense resistor R SENS .
This value can be used to calculate battery pack current using the equation below.)
2 7
2 6
2 5
2 4
2 3
2 2
2 1
2 0
LSB
MSb
(unit = 0.2441mV)
LSb
S
S
S
S
S
S
2 9
2 8
MSB
The battery pack current is calculated from the Current Register value using the equation:
I = Current Register / (4096 * R SENS )
(where R SENS is in W )
For example, if 1.25A is flowing into the pack, and the pack uses a 0.025 W sense resistor, the DS2438
will write the value 128 10 to the Current Register. From this value, battery pack current can be calculated
to be:
I = 128 / ( 4096 * 0.025) = 1.25A
Because small current ADC offset errors can have a large cumulative effect when current is integrated
over time, the DS2438 provides a method for canceling offset errors in the current ADC. After each
current measurement is completed, the measured value is added to the contents of the Offset Register and
the result is then stored in the Current Register. The Offset Register is a two-byte nonvolatile read/write
register formatted in two’s-complement format. The four MSb’s of the register contain the sign of the
offset, as shown in Table 4.
OFFSET REGISTER FORMAT Table 4
2 4
2 3
2 2
2 1
2 0
0
0
0
LSB
MSb
(unit = 0.2441 mV)
LSb
X
X
X
S
2 8
2 7
2 6
2 5
MSB
The following process can be used to calibrate the current ADC:
1. Write all zeroes to the Offset Register
2. Force zero current through R SENS
3. Read the Current Register value
4. Disable the current ADC by setting the IAD bit in the Status/Configuration Register to “0”
5. Change the sign of the previously-read Current Register value by performing the two’s complement
and write the result to the Offset Register
6. Enable the current ADC by setting the IAD bit in the Status/Configuration Register to “1”
NOTE:
When writing to the Offset Register, current measurement MUST be disabled (IAD bit set to “0”).
The current ADC calibration process is done for each DS2438 device prior to shipment. However, for
best results, battery pack manufacturers should calibrate the current ADC during initial battery pack
testing, and the host system should calibrate whenever possible (during battery charging, for example).
6 of 29
相关PDF资料 |
PDF描述 |
|---|---|
| DS2703U+ | IC BATT AUTHENTICATE SHA-1 8UMAX |
| DS2705U+ | IC AUTHENTICATE SHA-1 8-UMAX |
| DS2710G+ | IC NIMH CHRGR SGL-CELL 10-TDFN |
| DS2712Z+T&R | IC NIMH CHARGER 16SOIC |
| DS2714E+ | IC NIMH CHARGER QUAD 20TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS244 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Octal Buffer/Line Driver with 3-State Outputs |
| DS2441 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:1-Cell Li-Ion Battery Manager |
| DS2442 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Battery Management |
| DS245 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Octal Bus Transceiver |
| DS2450 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:1-Wire Quad A/D Converter |
发布紧急采购，3分钟左右您将得到回复。