- 您现在的位置：买卖IC网 > PDF目录1915 > DS2480B+ (Maxim Integrated Products)IC LINE DRVR W/SENSOR 1-W 8-SOIC PDF资料下载
参数资料
| 型号： | DS2480B+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/32页 |
| 文件大小： | 0K |
| 描述： | IC LINE DRVR W/SENSOR 1-W 8-SOIC |
| 产品培训模块： | 1-Wire Communications Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 类型： | 线路驱动器，发射器 |
| 驱动器/接收器数： | 1/0 |
| 规程： | RS232 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
| 产品目录页面： | 1429 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
DS2480B
Maxim Integrated........................................................................................................................................................................................... 18
PULSE WAVEFORMS, DISARMED
The Pulse command can be used to generate a strong pullup to 5V and a 12V programming pulse,
respectively. The duration of the pulse is predefined if the parameter value code of parameter 010
(Programming Pulse Duration) has a value from 000 to 110, and parameter 011 (Strong Pullup Duration)
has a value from 000 to 101 (see Table 4). Figures 7a and 7b show the timing of a pulse with predefined
duration, which should be considered the normal case. If infinite duration is chosen (parameter value code
111), the host must terminate the Pulse command, as shown in Figures 7c and 7d. All versions of Figure 7
assume that bit 1 of the pulse command is 0, i.e., disarmed mode. See the Communication Commands:
Pulse section for more details on possibilities of the Pulse command.
Figure 7a. STRONG PULLUP TO 5V, PREDEFINED DURATION
The processing of a pulse command is essentially the same, regardless if a strong pullup or a
programming pulse is requested. At t1 the host starts sending the pulse command byte. At t2 the DS2480B
has received the command and immediately generates the pulse. The pulse ends at t3 and the DS2480B
sends out the command response byte to inform the host that the command is completed. The idle time
between t1 and t2 is determined by the time to transmit the command byte at the selected baud rate. The
idle time between t3 and t4 is comprised of the time to transmit the response byte, plus the response time
of the host plus the time to transmit the command and/or data to generate the next time slot.
Figure 7b. 12V PROGRAMMING PULSE, PREDEFINED DURATION
A correct programming pulse can only be generated if the 12V programming voltage is available at the
VPP pin of the DS2480B. The rising and falling edges of the programming pulse are actively controlled by
DS2480B. The slew rate is approximately 14V/s and meets the requirements of 1-Wire EPROM
devices.
相关PDF资料 |
PDF描述 |
|---|---|
| DS2482X-100+T | IC MASTER I2C-1WIRE 1CH 9-WLP |
| DS2482X-101+T | IC MASTER I2C-1WIRE 1CH 9-WLP |
| DS2483Q+T | IC I2C TO 1WIRE BRIDGE 8TDFN |
| DS2490Y | IC BRIDGE CLIP USB TO 1-W 24SOIC |
| DS26303LN-75+A3 | IC LIU E1/T1/J1 3.3V 144-ELQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2480B | 制造商:Maxim Integrated Products 功能描述:IC SERIAL LINE DRIVER 2480 SOIC8 |
| DS2480B/T&R | 功能描述:缓冲器和线路驱动器 RoHS:否 制造商:Micrel 输入线路数量:1 输出线路数量:2 极性:Non-Inverting 电源电压-最大:+/- 5.5 V 电源电压-最小:+/- 2.37 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Reel |
| DS2480B+ | 功能描述:缓冲器和线路驱动器 Serial - 1-Wire Line Driver RoHS:否 制造商:Micrel 输入线路数量:1 输出线路数量:2 极性:Non-Inverting 电源电压-最大:+/- 5.5 V 电源电压-最小:+/- 2.37 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Reel |
| DS2480B+R | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Serial to 1-Wire Line Driver |
| DS2480B+T | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Serial to 1-Wire Line Driver |
发布紧急采购，3分钟左右您将得到回复。