- 您现在的位置：买卖IC网 > PDF目录1915 > DS2480B+ (Maxim Integrated Products)IC LINE DRVR W/SENSOR 1-W 8-SOIC PDF资料下载
参数资料
| 型号： | DS2480B+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 11/32页 |
| 文件大小： | 0K |
| 描述： | IC LINE DRVR W/SENSOR 1-W 8-SOIC |
| 产品培训模块： | 1-Wire Communications Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 类型： | 线路驱动器，发射器 |
| 驱动器/接收器数： | 1/0 |
| 规程： | RS232 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
| 产品目录页面： | 1429 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
DS2480B
Maxim Integrated........................................................................................................................................................................................... 19
For EPROM programming, only a single slave device should be connected to the 1-Wire bus and the
cable must to be short, not to exceed a few meters. One should not attempt generating a programming
pulse with a non-EPROM device on the bus; this may damage the device as well as the DS2480B.
Certain applications may require a duration for a strong pullup or programming pulse that cannot be
realized using one of the predefined values. Selecting infinite duration allows the host to generate pulses
of any length. As a consequence, however, the host becomes responsible to actively control the duration
of the pulse. Failing to do so may require a power-on reset or master reset cycle of the DS2480B. For this
reason, infinite duration should only be used if absolutely necessary.
The time to end a pulse of infinite duration strongly depends on the baud rate of the communication
between host and DS2480B. Neglecting the response time of the host, the minimum pulse durations are:
86.8s at 115.2kbps, 173.6s at 57.6kbps, 520s at 19.2kbps, and 1.04ms at 9.6kbps.
Figure 7c. STRONG PULLUP TO 5V, INFINITE DURATION
As before, processing the command is essentially the same, regardless if it is for a strong pullup or a
programming pulse. At t1 the host starts sending the Pulse command byte. At t2 the DS2480B has
received the command and immediately activates the strong pullup or switches in the 12V programming
voltage. To end the pulse, the DS2480B must receive a Termination command, code F1h, which occurs at
t3. The Termination command does not generate a response byte. The DS2480B will immediately end the
pulse and send out the response byte of the pulse command. The idle time between t1 and t2 is determined
by the time to transmit the command byte at the selected baud rate. The idle time between t3 and t4 is
comprised of the time to transmit the pulse response byte, plus the response time of the host plus the time
to transmit the command and/or data to generate the next time slot.
Figure 7d. 12V PROGRAMMING PULSE, INFINITE DURATION
相关PDF资料 |
PDF描述 |
|---|---|
| DS2482X-100+T | IC MASTER I2C-1WIRE 1CH 9-WLP |
| DS2482X-101+T | IC MASTER I2C-1WIRE 1CH 9-WLP |
| DS2483Q+T | IC I2C TO 1WIRE BRIDGE 8TDFN |
| DS2490Y | IC BRIDGE CLIP USB TO 1-W 24SOIC |
| DS26303LN-75+A3 | IC LIU E1/T1/J1 3.3V 144-ELQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2480B | 制造商:Maxim Integrated Products 功能描述:IC SERIAL LINE DRIVER 2480 SOIC8 |
| DS2480B/T&R | 功能描述:缓冲器和线路驱动器 RoHS:否 制造商:Micrel 输入线路数量:1 输出线路数量:2 极性:Non-Inverting 电源电压-最大:+/- 5.5 V 电源电压-最小:+/- 2.37 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Reel |
| DS2480B+ | 功能描述:缓冲器和线路驱动器 Serial - 1-Wire Line Driver RoHS:否 制造商:Micrel 输入线路数量:1 输出线路数量:2 极性:Non-Inverting 电源电压-最大:+/- 5.5 V 电源电压-最小:+/- 2.37 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Reel |
| DS2480B+R | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Serial to 1-Wire Line Driver |
| DS2480B+T | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Serial to 1-Wire Line Driver |
发布紧急采购，3分钟左右您将得到回复。