- 您现在的位置：买卖IC网 > PDF目录16238 > DS2776G+ (Maxim Integrated Products)IC FUEL GAUGE LI+ 2CELL 14-TDFN PDF资料下载
参数资料
| 型号： | DS2776G+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 18/46页 |
| 文件大小： | 0K |
| 描述： | IC FUEL GAUGE LI+ 2CELL 14-TDFN |
| 产品培训模块： | 1-Wire Communications Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 60 |
| 功能： | 燃料，电量检测计/监控器 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 4 V ~ 9.2 V |
| 工作温度： | -20°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-WFDFN 裸露焊盘 |
| 供应商设备封装： | 14-TDFN-EP（3x5） |
| 包装： | 管件 |
| 产品目录页面： | 1436 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页
2-Cell, Stand-Alone, Li+ Fuel-Gauge IC with
Protector and Optional SHA-1 Authentication
Accumulation Bias
In some designs a systematic error or an application
preference requires the application of an arbitrary bias
to the current accumulation process. The Current
Accumulation Bias register (CAB) allows a user-pro-
grammed constant positive or negative polarity bias to
be included in the current accumulation process. The
value in CAB can be used to estimate battery currents
that do not flow through the sense resistor, estimate
battery self-discharge, or estimate current levels below
the current measurement resolution. The user-pro-
grammed two’s complement value, with bit weighting
the same as the current register, is added to the ACR
once per current conversion cycle. CAB is loaded on
power-up from EEPROM memory.
Cycle Counter
The cycle counter is an absolute count of the cumula-
tive discharge cycles. This register is intended to act as
a “cell odometer.” The LSb is two cycles, which allows
a maximum count of 510 discharge cycles. The register
does not loop. Once the maximum value is reached,
the register is clamped. This register is read and write
accessible while the parameter EEPROM memory block
(block 1) is unlocked. The Cycle Count register
becomes read-only once the EEPROM block is locked.
Capacity Estimation Algorithm
Remaining capacity estimation uses real-time mea-
sured values and stored parameters describing the cell
characteristics and application operating limits. Figure
13 describes the algorithm inputs and outputs.
Modeling Cell Characteristics
To achieve reasonable accuracy in estimating remain-
ing capacity, the cell performance characteristics over
temperature, load current, and charge-termination point
must be considered. Since the behavior of Li+ cells is
nonlinear, these characteristics must be included in the
capacity estimation to achieve an acceptable level of
accuracy in the capacity estimation. The FuelPack
method used in the DS2775–DS2778 is described in
general in Application Note 131: Lithium-Ion Cell Fuel
Gauging with Maxim Battery Monitor ICs. To facilitate
efficient implementation in hardware, a modified version
of the method outlined in Application Note 131 is used
to store cell characteristics in the DS2775–DS2778. Full
and empty points are retrieved in a lookup process that
retraces a piecewise linear model consisting of three
model curves named full, active empty, and standby
empty. Each model curve is constructed with five line
segments, numbered 1 through 5. Above +40°C, the
segment 5 model curves extend infinitely with zero
slope, approximating the nearly flat change in capacity
of Li+ cells at temperatures above +40°C. Segment 4 of
each model curves originates at +40°C on its upper end
and extends downward in temperature to the junction
with segment 3. Segment 3 joins with segment 2, which
in turn joins with segment 1. Segment 1 of each model
curve extends from the junction with segment 2 to infi-
nitely colder temperatures. The three junctions or break-
points that join the segments (labeled TBP12, TBP23,
and TBP34 in Figure 14) are programmable in 1°C
increments from -128°C to +40°C. The slope or deriva-
tive for segments 1, 2, 3, and 4 are also programmable
over a range of 0 to 15,555ppm in steps of 61ppm.
ADDRESS 61h
S
2 6
2 5
2 4
2 3
2 2
2 1
2 0
MSb
“S ”: SIGN BIT(S)
Figure 11. Current Accumulation Bias Register Format
ADDRESS 1Eh
LSb
UNITS: 6.25 μV/R SNS
2 7
2 6
2 5
2 4
2 3
2 2
2 1
2 0
MSb
LSb
UNITS: 2 cycles
Figure 12. Cycle Counter Register Format
18
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| DS2788E+ | IC FUEL GAUGE W/DSP DRV 14TSSOP |
| EEM18DSEF-S243 | CONN EDGECARD 36POS .156 EYELET |
| UCS2C331MHD | CAP ALUM 330UF 160V 20% RADIAL |
| KS8993-EVAL | BOARD EVAL EXPERIMENT FOR KS8993 |
| UVR2W470MHD | CAP ALUM 47UF 450V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2776G+ | 功能描述:电池管理 2-Cell Stand-Alone Li+ Fuel-Gauge RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| DS2776G+T&R | 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:2S FG PROT SHA-1 1W 14L 3X5 TDFN T& - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC FUEL GAUGE LI+ 2CELL 14-TDFN |
| DS2776G+T&R | 功能描述:电池管理 2-Cell Stand-Alone Li+ Fuel-Gauge RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| DS2776K | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| DS2777 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:2-Cell, Stand-Alone, Li+ Fuel-Gauge IC with Protector and Optional SHA-1 Authentication |
发布紧急采购，3分钟左右您将得到回复。