- 您现在的位置：买卖IC网 > PDF目录16240 > DS2782E+ (Maxim Integrated Products)IC FUEL GAUGE BATT 8TSSOP PDF资料下载
参数资料
| 型号： | DS2782E+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 13/28页 |
| 文件大小： | 0K |
| 描述： | IC FUEL GAUGE BATT 8TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 功能： | 燃料，电量检测计/监控器 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 2.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 8-TSSOP |
| 包装： | 管件 |
| 产品目录页面： | 1436 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
DS2782
MODELING CELL CHARACTERISTICS
In order to achieve reasonable accuracy in estimating remaining capacity, the cell performance characteristics over
temperature, load current, and charge termination point must be considered. Since the behavior of Li-ion cells is
non-linear, even over a limited temperature range of 10°C to 35°C, these characteristics must be included in the
capacity estimation to achieve a reasonable accuracy. Refer to Application Note AN131: Li+ Fuel Gauging with
Dallas Semiconductor Devices for general information on the FuelPack? method used in the DS2782. To facilitate
efficient implementation in hardware, a modified version of the method outlined in AN131 is used to store cell
characteristics in the DS2782. Full and empty points are retrieved in a lookup process which re-traces a piece-wise
linear model. Three model curves are stored: Full, Active Empty and Standby Empty. Each model curve is
constructed with 4 line segments and spans from 0°C to 40°C. Operation outside the 0°C to 40°C model span is
supported by the model with minimal loss of accuracy. Above 40°C, the 40°C fixed points are extended with zero
slope. This achieves a conservative capacity estimate for temperatures above 40°C. Below 0°C, the model curves
are extended using the slope of each 0°C to 10°C segment. If low temperature operation is expected, the 0°C to
10°C slopes can be selected to optimize the model accuracy. A diagram of example battery cell model curves is
shown if Figure 12.
Figure 12. Cell Model Example Diagram
100%
Derivative
[ppm / °C]
FULL
Active
Empty
Standby
Empty
Cell
Characterization
data points
1
2
3
4
0°C
10°C
20°C
30°C
40°C
Full: The Full curve defines how the full point of a given cell depends on temperature for a given charge
termination. The charge termination method used in the application is used to determine the table values. The
DS2782 reconstructs the Full line from cell characteristic table values to determine the Full capacity of the battery
at each temperature. Reconstruction occurs in one-degree temperature increments.
Active Empty: The Active Empty curve defines the temperature variation in the empty point of the discharge profile
based on a high level load current (one that is sustained during a high power operating mode) and the minimum
voltage required for system operation. This load current is programmed as the Active Empty current (IAE), and
should be a 3.5s average value to correspond to values read from the Current register, and the specified minimum
voltage, or Active Empty voltage (VAE) should be a 220ms average to correspond to values read from the Voltage
register. The DS2782 reconstructs the Active Empty line from cell characteristic table values to determine the
Active Empty capacity of the battery at each temperature. Reconstruction occurs in one-degree temperature
increments.
Standby Empty: The Standby Empty curve defines the temperature variation in the empty point in the discharge
defined by the application standby current and the minimum voltage required for standby operation. In typical PDA
FuelPack is a trademark of Maxim Integrated Products, Inc.
13 of 28
相关PDF资料 |
PDF描述 |
|---|---|
| M1DXK-5036J | IDC CABLE - MKR50K/MC50G/X |
| M1BXK-5036J | IDC CABLE - MSR50K/MC50G/X |
| DS2438AZ+ | IC MONITOR SMART BATTERY 8-SOIC |
| M3TTK-3406J | IDC CABLE - MSD34K/MC34G/MSD34K |
| M3UGK-2018J | IDC CABLE - MKS20K/MC20G/MCS20K |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2782E+ | 功能描述:电池管理 Stand-Alone Fuel Gauge RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| DS2782E+R | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Stand-Alone Fuel Gauge IC |
| DS2782E+T | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Stand-Alone Fuel Gauge IC |
| DS2782E+T&R | 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:FUEL GAUGE LI-ION/LI-POL 8TSSOP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC FUEL GAUGE BATT 8TSSOP |
| DS2782E+T&R | 功能描述:电池管理 Stand-Alone Fuel Gauge RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。