- 您现在的位置：买卖IC网 > PDF目录16240 > DS2782E+ (Maxim Integrated Products)IC FUEL GAUGE BATT 8TSSOP PDF资料下载
参数资料
| 型号： | DS2782E+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 16/28页 |
| 文件大小： | 0K |
| 描述： | IC FUEL GAUGE BATT 8TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 功能： | 燃料，电量检测计/监控器 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 2.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 8-TSSOP |
| 包装： | 管件 |
| 产品目录页面： | 1436 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
DS2782
CAPACITY ESTIMATION UTILITY FUNCTIONS
Aging Estimation
As discussed above, the AS register value is adjusted occasionally based on cumulative discharge. As the ACR
register decrements during each discharge cycle, an internal counter is incremented until equal to 32 times AC. AS
is then decremented by one, resulting in a decrease in the scaled full battery capacity of 0.78%. Refer to the AC
register description above for recommendations on customizing the age estimation rate.
Learn Function
Since Li+ cells exhibit charge efficiencies near unity, the charge delivered to a Li+ cell from a known empty point to
a known full point is a dependable measure of the cell capacity. A continuous charge from empty to full results in a
“learn cycle”. First, the Active Empty point must be detected. The Learn Flag ( LEARNF ) is set at this point. Then,
once charging starts, the charge must continue uninterrupted until the battery is charged to full. Upon detecting full,
LEARNF is cleared, the Charge to Full ( CHGTF ) flag is set and the Age Scalar (AS) is adjusted according to the
learned capacity of the cell.
ACR Housekeeping
The ACR register value is adjusted occasionally to maintain the coulomb count within the model curve boundaries.
When the battery is charged to full ( CHGTF set), the ACR is set equal to the age scaled full lookup value at the
present temperature. If a learn cycle is in progress, correction of the ACR value occurs after the age scalar (AS) is
updated.
When an empty condition is detected ( AEF or LEARNF set), the ACR adjustment is conditional. If AEF is set and
LEARNF is not, then the Active Empty Point was not detected and the battery is likely below the Active Empty
capacity of the model. The ACR is set to the Active Empty model value only if it is greater than the Active Empty
model value. If LEARNF is set, then the battery is at the Active Empty Point and the ACR is set to the Active Empty
model value.
Full Detect
Full detection occurs when the Voltage (VOLT) readings remain continuously above the VCHG threshold for the
period between two Average Current (IAVG) readings, where both IAVG readings are below IMIN. The two
consecutive IAVG readings must also be positive and non-zero. This ensures that removing the battery from the
charger does not result in a false detection of full. Full Detect sets the Charge to Full ( CHGTF ) bit in the Status
register.
Active Empty Point Detect
Active Empty Point detection occurs when the Voltage register drops below the VAE threshold and the two
previous Current readings are above IAE. This captures the event of the battery reaching the Active Empty point.
Note that the two previous Current readings must be negative and greater in magnitude than IAE, that is, a larger
discharge current than specified by the IAE threshold. Qualifying the Voltage level with the discharge rate ensures
that the Active Empty point is not detected at loads much lighter than those used to construct the model. Also,
Active Empty must not be detected when a deep discharge at a very light load is followed by a load greater than
IAE. Either case would cause a learn cycle on the following charge to full to include part of the Standby capacity in
the measurement of the Active capacity. Active Empty detection sets the Learn Flag ( LEARNF ) bit in the Status
register.
16 of 28
相关PDF资料 |
PDF描述 |
|---|---|
| M1DXK-5036J | IDC CABLE - MKR50K/MC50G/X |
| M1BXK-5036J | IDC CABLE - MSR50K/MC50G/X |
| DS2438AZ+ | IC MONITOR SMART BATTERY 8-SOIC |
| M3TTK-3406J | IDC CABLE - MSD34K/MC34G/MSD34K |
| M3UGK-2018J | IDC CABLE - MKS20K/MC20G/MCS20K |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2782E+ | 功能描述:电池管理 Stand-Alone Fuel Gauge RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| DS2782E+R | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Stand-Alone Fuel Gauge IC |
| DS2782E+T | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Stand-Alone Fuel Gauge IC |
| DS2782E+T&R | 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:FUEL GAUGE LI-ION/LI-POL 8TSSOP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC FUEL GAUGE BATT 8TSSOP |
| DS2782E+T&R | 功能描述:电池管理 Stand-Alone Fuel Gauge RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。