- 您现在的位置：买卖IC网 > PDF目录16240 > DS2782E+ (Maxim Integrated Products)IC FUEL GAUGE BATT 8TSSOP PDF资料下载
参数资料
| 型号： | DS2782E+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/28页 |
| 文件大小： | 0K |
| 描述： | IC FUEL GAUGE BATT 8TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 功能： | 燃料，电量检测计/监控器 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 2.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 8-TSSOP |
| 包装： | 管件 |
| 产品目录页面： | 1436 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
DS2782
POWER MODES
The DS2782 has two power modes: ACTIVE and SLEEP. On initial power up, the DS2782 defaults to ACTIVE
mode. While in ACTIVE mode, the DS2782 is fully functional with measurements and capacity estimation
continuously updated. In SLEEP mode, the DS2782 conserves power by disabling measurement and capacity
estimation functions, but preserves register contents. SLEEP mode is entered under two different conditions and
an enable bit for each condition makes entry into SLEEP optional. SLEEP mode can be enabled using the Power
Mode (PMOD) bit or the Under Voltage Enable (UVEN) bit.
The PMOD type SLEEP is entered if the PMOD bit is set AND a bus low condition occurs. A bus low condition,
where both SDA AND SCL low for t SLEEP (2s nominal), is used to detect a pack disconnection or system shutdown
in which the bus pull-up voltage, V PULLUP , is not present. PMOD SLEEP assumes that no charge or discharge
current will flow and therefore coulomb counting is not necessary. A system with PMOD SLEEP enabled must
ensure that a stand-alone or cradle charger includes a pull-up on SDA and/or SCL. The DS2782 transitions from
PMOD SLEEP to ACTIVE mode when either SDA or SCL is pulled high.
The second option for entering SLEEP is an under voltage condition measured on VIN. When the UVEN bit is set,
the DS2782 will transition to SLEEP if the voltage on VIN is less than V SLEEP (2.45V nominal) AND the 2-Wire bus
is in a bus high or a bus low condition for t SLEEP . UVEN SLEEP relieves the battery of the DS2782 load until
communication resumes to prevent over discharging the battery. The DS2782 transitions from UVEN SLEEP to
ACTIVE mode when either SDA or SCL change logic state. The bus master should initiate a transaction after
charging of a depleted battery begins.
Note: PMOD and UVEN SLEEP features must be disabled when a battery is charged on an external charger that
does not connect to SDA and/or SCL. PMOD SLEEP can be used if the charger pulls the bus high. The DS2782
remains in SLEEP and therefore does not measure or accumulate current when a battery is charged on a charger
that fails to properly drive the communication bus.
INITIATING COMMUNICATION IN SLEEP
When beginning communication with a DS2782 in PMOD SLEEP, the bus must be pulled up before a START bit
can be issued by the master. In UVEN SLEEP, the procedure depends on the bus state when UVEN SLEEP was
entered. If the bus was low, it must be pulled up before a START bit can be issued by the master as required with
PMOD SLEEP. If the bus was high when UVEN SLEEP was entered, then the DS2782 is prepared to receive a
START bit from the master. A standard procedure of issuing a START – STOP – START when the host system is
powered up on the charger input properly initiates communication from both PMOD and UVEN SLEEP modes.
VOLTAGE MEASUREMENT
Battery voltage is measured at the VIN input with respect to VSS over a range of 0V to 4.5V, with a resolution of
4.88mV. The result is updated every 440ms and placed in the VOLTAGE register in two’s complement form.
Voltages above the maximum register value are reported at the maximum value; voltages below the minimum
register value are reported at the minimum value. The format of the voltage register is shown in Figure 4.
Figure 4. Voltage Register Format
VOLT
MSB—Address 0Ch
LSB—Address 0Dh
Read Only
S
2 9
2 8
2 7
2 6
2 5
2 4
2 3
2 2
2 1
2 0
X
X
X
X
X
MSb
“S”: sign bit(s), “X”: reserved
LSb
MSb
LSb
Units: 4.88mV
7 of 28
相关PDF资料 |
PDF描述 |
|---|---|
| M1DXK-5036J | IDC CABLE - MKR50K/MC50G/X |
| M1BXK-5036J | IDC CABLE - MSR50K/MC50G/X |
| DS2438AZ+ | IC MONITOR SMART BATTERY 8-SOIC |
| M3TTK-3406J | IDC CABLE - MSD34K/MC34G/MSD34K |
| M3UGK-2018J | IDC CABLE - MKS20K/MC20G/MCS20K |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2782E+ | 功能描述:电池管理 Stand-Alone Fuel Gauge RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| DS2782E+R | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Stand-Alone Fuel Gauge IC |
| DS2782E+T | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Stand-Alone Fuel Gauge IC |
| DS2782E+T&R | 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:FUEL GAUGE LI-ION/LI-POL 8TSSOP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC FUEL GAUGE BATT 8TSSOP |
| DS2782E+T&R | 功能描述:电池管理 Stand-Alone Fuel Gauge RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。