- 您现在的位置：买卖IC网 > PDF目录16240 > DS2782E+ (Maxim Integrated Products)IC FUEL GAUGE BATT 8TSSOP PDF资料下载
参数资料
| 型号： | DS2782E+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 9/28页 |
| 文件大小： | 0K |
| 描述： | IC FUEL GAUGE BATT 8TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 功能： | 燃料，电量检测计/监控器 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 2.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 8-TSSOP |
| 包装： | 管件 |
| 产品目录页面： | 1436 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
DS2782
AVERAGE CURRENT MEASUREMENT
The Average Current register reports an average current level over the preceding 28 seconds. The register value is
updated every 28s in two’s complement form, and is the average of the 8 preceding Current register updates. The
format of the Average Current register is shown in Figure 7. Charge currents above the maximum register value
are reported at the maximum value (7FFFh = +51.2mV). Discharge currents below the minimum register value are
reported at the minimum value (8000h = -51.2mV).
Figure 7. Average Current Register Format
IAVG
MSB—Address 08h
LSB—Address 09h
R/W
S
2 14
2 13
2 12
2 11
2 10
2 9
2 8
2 7
2 6
2 5
2 4
2 3
2 2
2 1
2 0
MSb
“S”: sign bit(s)
LSb
MSb
Units:
LSb
1.5625 ? V/Rsns
CURRENT OFFSET CORRECTION
Every 1024th conversion, the ADC measures its input offset to facilitate offset correction. Offset correction occurs
approximately once per hour. The resulting correction factor is applied to the subsequent 1023 measurements.
During the offset correction conversion, the ADC does not measure the sense resistor signal. A maximum error of
1/1024 in the accumulated current register (ACR) is possible; however, to reduce the error, the current
measurement made just prior to the offset conversion is displayed in the current register and is substituted for the
dropped current measurement in the current accumulation process. This results in an accumulated current error
due to offset correction of less than 1/1024.
CURRENT MEASUREMENT CALIBRATION
The DS2782’s current measurement gain can be adjusted through the RSGAIN register, which is factory-calibrated
to meet the data sheet specified accuracy. RSGAIN is user accessible and can be reprogrammed after module or
pack manufacture to improve the current measurement accuracy. Adjusting RSGAIN can correct for variation in an
external sense resistor’s nominal value, and allows the use of low-cost, non-precision current sense resistors.
RSGAIN is an 11-bit value stored in 2 bytes of the Parameter EEPROM Memory Block. The RSGAIN value adjusts
the gain from 0 to 1.999 in steps of 0.001 (precisely 2 -10 ). The user must program RSGAIN cautiously to ensure
accurate current measurement. When shipped from the factory, the gain calibration value is stored in two separate
locations in the Parameter EEPROM Block: RSGAIN, which is reprogrammable, and FRSGAIN, which is read only.
RSGAIN determines the gain used in the current measurement. The read-only FRSGAIN is provided to preserve
the factory value only and is not used in the current measurement.
SENSE RESISTOR TEMPERATURE COMPENSATION
The DS2782 is capable of temperature compensating the current sense resistor to correct for variation in a sense
resistor’s value over temperature. The DS2782 is factory programmed with the sense resistor temperature
coefficient, RSTC, set to zero, which turns off the temperature compensation function. RSTC is user accessible
and can be reprogrammed after module or pack manufacture to improve the current accuracy when using a high
temperature coefficient current-sense resistor. RSTC is an 8-bit value stored in the Parameter EEPROM Memory
Block. The RSTC value sets the temperature coefficient from 0 to +7782ppm/oC in steps of 30.5ppm/oC. The user
must program RSTC cautiously to ensure accurate current measurement.
Temperature compensation adjustments are made when the Temperature register crosses 0.5 o C boundaries. The
temperature compensation is most effective with the resistor placed as close as possible to the VSS terminal to
optimize thermal coupling of the resistor to the on-chip temperature sensor. If the current shunt is constructed with
a copper PCB trace, run the trace under the DS2782 package if possible.
9 of 28
相关PDF资料 |
PDF描述 |
|---|---|
| M1DXK-5036J | IDC CABLE - MKR50K/MC50G/X |
| M1BXK-5036J | IDC CABLE - MSR50K/MC50G/X |
| DS2438AZ+ | IC MONITOR SMART BATTERY 8-SOIC |
| M3TTK-3406J | IDC CABLE - MSD34K/MC34G/MSD34K |
| M3UGK-2018J | IDC CABLE - MKS20K/MC20G/MCS20K |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2782E+ | 功能描述:电池管理 Stand-Alone Fuel Gauge RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| DS2782E+R | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Stand-Alone Fuel Gauge IC |
| DS2782E+T | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Stand-Alone Fuel Gauge IC |
| DS2782E+T&R | 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:FUEL GAUGE LI-ION/LI-POL 8TSSOP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC FUEL GAUGE BATT 8TSSOP |
| DS2782E+T&R | 功能描述:电池管理 Stand-Alone Fuel Gauge RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。