参数资料
| 型号： | DS33Z44+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 4/59页 |
| 文件大小： | 0K |
| 描述： | IC MAPPER ETHERNET 256CSBGA |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 40 |
| 应用： | 数据传输 |
| 接口： | 串行 |
| 电源电压： | 1.8V，2.5V，3.3V |
| 封装/外壳： | 256-LBGA，CSBGA |
| 供应商设备封装： | 256-CSBGA（17x17） |
| 包装： | 托盘 |
| 安装类型： | 表面贴装 |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页
DS33Z44DK
12 of 59
Quick Setup #2 (DS3174 T3E3)
On the DS3174 serial resource card install jumper J24. Jumpers JP16–JP19 should be set high. This places
the card in DS3174 mode and enables all four ports as described in Table 3.
Complete the hardware configuration and one of the basic DS33Z44 configurations as previously described.
Using a patch cable, connect the Ethernet connector to an ordinary PC, or network test equipment. This should
cause the link LED to turn on.
Launch ChipView.exe (or use existing session if it is already open) and select Register View. When prompted
for a definition file, pick the file name ds3184_evbrd_reduced.def. After the definition file loads, go to the File
menu and select File→Memory Config File→Load .MFG file. When prompted, select the file named
84_t3_sct_needscoaxlb.mfg
.
Place a loopback connector at the DS3174 network side.
At this point, any packets sent to the DS33Z44 are echoed back. Incoming packets (i.e., ping) should cause the
RX LED to blink, after which the TX LED should also blink.
Quick Setup #3 (DS21458 T1E1)
Complete the hardware configuration and one of the basic DS33Z44 configurations as previously described.
Using a patch cable, connect the Ethernet connector to an ordinary PC, or network test equipment. This should
cause the link LED to turn on.
Launch ChipView.exe (or use existing session if it is already open) and select Register View. When prompted
for a definition file, pick the file named DS21458.def. After the definition file loads, go to the File menu and
select File
→Reg Ini File→Load Ini File. When prompted, pick the file named
e1_gapclk_crc4_hdb3_nocas.ini
.
Place a loopback connector at the DS21458 network side; RLOS LED should go out.
At this point any packets sent to the DS33Z44 are echoed back. Incoming packets (i.e. ping) should cause the
RX LED to blink, after which the TX LED should also blink.
相关PDF资料 |
PDF描述 |
|---|---|
| DS33ZH11+ | IC MAPPER ETHERNET 100CSBGA |
| DS34C87TN/NOPB | IC LINE DRIVER QUAD CMOS 16-DIP |
| DS34LV87TMX/NOPB | IC LINE DVR QUAD CMOS DIF 16SOIC |
| DS34S132GN+ | IC TDM OVER PACKET 676-BGA |
| DS34T102GN+ | IC TDM OVER PACKET 484TEBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS33Z44+ | 功能描述:网络控制器与处理器 IC Quad Ethernet Mapper RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS33Z44DK | 功能描述:以太网开发工具 DS33Z44 Dev Kit RoHS:否 制造商:Micrel 产品:Evaluation Boards 类型:Ethernet Transceivers 工具用于评估:KSZ8873RLL 接口类型:RMII 工作电源电压: |
| DS33ZH11 | 功能描述:网络控制器与处理器 IC 10/100 ENETXPORT HMODE MAP IND RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS33ZH11+ | 功能描述:网络控制器与处理器 IC 10/100 ENETXPORT HMODE MAP IND RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS34 | 制造商:LUMILEDS 制造商全称:LUMILEDS 功能描述:power light source Luxeon V Emitter |
发布紧急采购，3分钟左右您将得到回复。