- 您现在的位置：买卖IC网 > PDF目录97870 > DS83C530-ENL (DALLAS SEMICONDUCTOR) 8-BIT, OTPROM, 33 MHz, MICROCONTROLLER, PQFP52 PDF资料下载
参数资料
| 型号： | DS83C530-ENL |
| 厂商： | DALLAS SEMICONDUCTOR |
| 元件分类： | Microcontroller |
| 英文描述： | 8-BIT, OTPROM, 33 MHz, MICROCONTROLLER, PQFP52 |
| 封装： | TQFP-52 |
| 文件页数： | 16/44页 |
| 文件大小： | 754K |
| 代理商： | DS83C530-ENL |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
DS87C530/DS83C530
23 of 44
SERIAL PORTS
The DS87C530/DS83C530 provides a serial port (UART) that is identical to the 80C52. In addition it
includes a second hardware serial port that is a full duplicate of the standard one. This port optionally
uses pins P1.2 (RXD1) and P1.3 (TXD1). It has duplicate control functions included in new SFR
locations.
Both ports can operate simultaneously but can be at different baud rates or even in different modes. The
second serial port has similar control registers (SCON1; C0h, SBUF1; C1h) to the original. The new
serial port can only use Timer 1 for timer-generated baud rates.
TIMER RATE CONTROL
There is one important difference between the DS87C530/DS83C530 and 8051 regarding timers. The
original 8051 used 12 clocks per cycle for timers as well as for machine cycles. The
DS87C530/DS83C530 architecture normally uses 4 clocks per machine cycle. However, in the area of
timers and serial ports, the DS87C530/DS83C530 will default to 12 clocks per cycle on reset. This allows
existing code with real-time dependencies such as baud rates to operate properly.
If an application needs higher speed timers or serial baud rates, the user can select individual timers to run
at the 4-clock rate. The Clock Control register (CKCON; 8Eh) determines these timer speeds. When the
relevant CKCON bit is a logic 1, the DS87C530/DS83C530 uses 4 clocks per cycle to generate timer
speeds. When the bit is a 0, the DS87C530 uses 12 clocks for timer speeds. The reset condition is a 0.
CKCON.5 selects the speed of Timer 2. CKCON.4 selects Timer 1 and CKCON.3 selects Timer 0.
Unless a user desires very fast timing, it is unnecessary to alter these bits. Note that the timer controls are
independent.
POWER-FAIL RESET
The DS87C530/DS83C530 uses a precision band-gap voltage reference to decide if VCC is out of
tolerance. While powering up, the internal monitor circuit maintains a reset state until VCC rises above
the VRST level. Once above this level, the monitor enables the crystal oscillator and counts 65536 clocks.
It then exits the reset state. This power-on reset (POR) interval allows time for the oscillator to stabilize.
A system needs no external components to generate a power-related reset. Anytime VCC drops below
VRST, as in power failure or a power drop, the monitor will generate and hold a reset. It occurs
automatically, needing no action from the software. Refer to the Electrical Specifications for the exact
value of VRST.
POWER-FAIL INTERRUPT
The voltage reference that sets a precise reset threshold also generates an optional early warning Power-
fail Interrupt (PFI). When enabled by software, the processor will vector to program memory address
0033h if VCC drops below VPFW. PFI has the highest priority. The PFI enable is in the Watchdog Control
SFR (WDCON - D8h). Setting WDCON.5 to a logic 1 will enable the PFI. Application software can also
read the PFI flag at WDCON.4. A PFI condition sets this bit to a 1. The flag is independent of the
interrupt enable and software must manually clear it. If the PFI is enabled and the band-gap select bit
(BGS) is set, a PFI will bring the device out of Stop mode.
WATCHDOG TIMER
To prevent software from losing control, the DS87C530/DS83C530 includes a programmable Watchdog
Timer. The Watchdog is a free running timer that sets a flag if allowed to reach a preselected time-out. It
can be (re)started by software.
相关PDF资料 |
PDF描述 |
|---|---|
| DS87C530-ECL | 8-BIT, OTPROM, 33 MHz, MICROCONTROLLER, PQFP52 |
| DS87C520-MCL | 8-BIT, OTPROM, MICROCONTROLLER, PDIP40 |
| DS87C520-QNL | 8-BIT, OTPROM, 33 MHz, MICROCONTROLLER, PQCC44 |
| DS87C520-QCL | 8-BIT, OTPROM, 33 MHz, MICROCONTROLLER, PQCC44 |
| DS87C520-ECL | 8-BIT, OTPROM, 33 MHz, MICROCONTROLLER, PQFP44 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS83C530-ENL+ | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:EPROM/ROM Microcontrollers with Real-Time Clock |
| DS83C530-QCL | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:EPROM/ROM Micro with Real Time Clock |
| DS83C530-QCL+ | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:EPROM/ROM Microcontrollers with Real-Time Clock |
| DS83C530-QNL | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:EPROM/ROM Microcontrollers with Real-Time Clock |
| DS83C530-QNL+ | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:EPROM/ROM Microcontrollers with Real-Time Clock |
发布紧急采购，3分钟左右您将得到回复。