- 您现在的位置：买卖IC网 > PDF目录97870 > DS83C530-QNL (MAXIM INTEGRATED PRODUCTS INC) 8-BIT, MROM, 33 MHz, MICROCONTROLLER, PQCC52 PDF资料下载
参数资料
| 型号： | DS83C530-QNL |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | Microcontroller |
| 英文描述： | 8-BIT, MROM, 33 MHz, MICROCONTROLLER, PQCC52 |
| 封装： | PLASTIC, LCC-52 |
| 文件页数： | 13/45页 |
| 文件大小： | 649K |
| 代理商： | DS83C530-QNL |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页
DS87C530/DS83C530 EPROM/ROM Microcontrollers with Real-Time Clock
20 of 45
Crystal/Ring Operation
The DS87C530/DS83C530 allow software to choose the clock source as an independent selection from
the instruction cycle rate. The user can select crystal-based or ring oscillator-based operation under
software control. Power-on reset default is the crystal (or external clock) source. The ring may save
power depending on the actual crystal speed. To save still more power, software can then disable the
crystal amplifier. This process requires two steps. Reversing the process also requires two steps.
The XT/ RG bit (EXIF.3) selects the crystal or ring as the clock source. Setting XT/ RG = 1 selects the
crystal. Setting XT/ RG = 0 selects the ring. The RGMD (EXIF.2) bit serves as a status bit by indicating
the active clock source. RGMD = 0 indicates the CPU is running from the crystal. RGMD = 1 indicates it
is running from the ring. When operating from the ring, disable the crystal amplifier by setting the
XTOFF bit (PMR.3) to a 1. This can only be done when XT/ RG = 0.
When changing the clock source, the selection will take effect after a one-instruction-cycle delay. This
applies to changes from crystal to ring and vise versa. However, this assumes that the crystal amplifier is
running. In most cases, when the ring is active, software previously disabled the crystal to save power. If
ring operation is being used and the system must switch to crystal operation, the crystal must first be
enabled. Set the XTOFF bit to 0. At this time, the crystal oscillation will begin. The
DS87C530/DS83C530 then provide a warm-up delay to make certain that the frequency is stable.
Hardware will set the XTUP bit (STATUS.4) to 1 when the crystal is ready for use. Then software should
write XT/ RG to 1 to begin operating from the crystal. Hardware prevents writing XT/ RG to 1 before
XTUP = 1. The delay between XTOFF = 0 and XTUP = 1 will be 65,536 crystal clocks in addition to the
crystal cycle startup time.
Switchback has no affect on the clock source. If software selects a reduced clock divider and enables the
ring, a Switchback will only restore the divider speed. The ring will remain as the time base until altered
by software. If there is serial activity, Switchback usually occurs with enough time to create proper baud
rates. This is not true if the crystal is off and the CPU is running from the ring. If sending a serial
character that wakes the system from crystal-less PMM, then it should be a dummy character of no
importance with a subsequent delay for crystal startup.
Table 6 is a summary of the bits relating to PMM and its operation. The flow chart below illustrates a
typical decision set associated with PMM.
相关PDF资料 |
PDF描述 |
|---|---|
| DS87C530-QNL | 8-BIT, OTPROM, 33 MHz, MICROCONTROLLER, PQCC52 |
| DS83C530-QCL | 8-BIT, MROM, 33 MHz, MICROCONTROLLER, PQCC52 |
| DS87C530-KCL | 8-BIT, OTPROM, 33 MHz, MICROCONTROLLER, CQCC52 |
| DTA-03D-1.5-TA-P | POSITION, LINEAR SENSOR-AC, -3-3mm |
| DTA-01D-3-SA-P | POSITION, LINEAR SENSOR-AC, -1-1mm |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS83C530-QNL+ | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:EPROM/ROM Microcontrollers with Real-Time Clock |
| DS83CH20 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Peripheral (Multifunction) Controller |
| DS84 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| DS840 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| DS843 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
发布紧急采购，3分钟左右您将得到回复。