- 您现在的位置：买卖IC网 > PDF目录97870 > DS83C530-QNL (MAXIM INTEGRATED PRODUCTS INC) 8-BIT, MROM, 33 MHz, MICROCONTROLLER, PQCC52 PDF资料下载
参数资料
| 型号： | DS83C530-QNL |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | Microcontroller |
| 英文描述： | 8-BIT, MROM, 33 MHz, MICROCONTROLLER, PQCC52 |
| 封装： | PLASTIC, LCC-52 |
| 文件页数： | 8/45页 |
| 文件大小： | 649K |
| 代理商： | DS83C530-QNL |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页
DS87C530/DS83C530 EPROM/ROM Microcontrollers with Real-Time Clock
16 of 45
Using a Stretch value between 1 and 7 causes the microcontroller to stretch the read/write strobe and all
related timing. Also, setup and hold times are increased by 1 clock when using any Stretch greater than 0.
This results in a wider read/write strobe and relaxed interface timing, allowing more time for
memory/peripherals to respond. The timing of the variable speed MOVX is in the Electrical
Specifications section. Table 3 shows the resulting strobe widths for each Stretch value. The memory
Stretch uses the Clock Control Special Function Register at SFR location 8Eh. The Stretch value is
selected using bits CKCON.2–0. In the table, these bits are referred to as M2 through M0. The first
Stretch (default) allows the use of common 120ns RAMs without dramatically lengthening the memory
access.
Table 3. Data Memory Cycle Stretch Values
CKCON.2–0
M2
M1
M0
MEMORY CYCLES
RD OR WR STROBE
WIDTH IN CLOCKS
STROBE WIDTH TIME
AT 33MHz
(ns)
0
2 (forced internal)
2
60
0
1
3 (default external)
4
121
0
1
0
4
8
242
0
1
5
12
364
1
0
6
16
485
1
0
1
7
20
606
1
0
8
24
727
1
9
28
848
DUAL DATA POINTER
The timing of block moves of data memory is faster using the Dual Data Pointer (DPTR). The standard
8051 DPTR is a 16-bit value that is used to address off-chip data RAM or peripherals. In the
DS87C530/DS83C530, the standard data pointer is called DPTR, located at SFR addresses 82h and 83h.
These are the standard locations. Using DPTR requires no modification of standard code. The new DPTR
at SFR 84h and 85h is called DPTR1. The DPTR Select bit (DPS) chooses the active pointer. Its location
is the lsb of the SFR location 86h. No other bits in register 86h have any effect and are 0. The user
switches between data pointers by toggling the lsb of register 86h. The increment (INC) instruction is the
fastest way to accomplish this. All DPTR-related instructions use the currently selected DPTR for any
activity. Therefore it takes only one instruction to switch from a source to a destination address. Using the
Dual Data Pointer saves code from needing to save source and destination addresses when doing a block
move. The software simply switches between DPTR and 1 once software loads them. The relevant
register locations are as follows.
DPL
82h
Low byte original DPTR
DPH
83h
High byte original DPTR
DPL1
84h
Low byte new DPTR
DPH1
85h
High byte new DPTR
DPS
86h
DPTR Select (lsb)
相关PDF资料 |
PDF描述 |
|---|---|
| DS87C530-QNL | 8-BIT, OTPROM, 33 MHz, MICROCONTROLLER, PQCC52 |
| DS83C530-QCL | 8-BIT, MROM, 33 MHz, MICROCONTROLLER, PQCC52 |
| DS87C530-KCL | 8-BIT, OTPROM, 33 MHz, MICROCONTROLLER, CQCC52 |
| DTA-03D-1.5-TA-P | POSITION, LINEAR SENSOR-AC, -3-3mm |
| DTA-01D-3-SA-P | POSITION, LINEAR SENSOR-AC, -1-1mm |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS83C530-QNL+ | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:EPROM/ROM Microcontrollers with Real-Time Clock |
| DS83CH20 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Peripheral (Multifunction) Controller |
| DS84 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| DS840 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| DS843 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
发布紧急采购，3分钟左右您将得到回复。