参数资料
型号: DSP56F807VF80
厂商: Freescale Semiconductor
文件页数: 52/60页
文件大小: 0K
描述: IC DSP 80MHZ 60K FLASH 160-BGA
标准包装: 126
系列: 56F8xx
核心处理器: 56800
芯体尺寸: 16-位
速度: 80MHz
连通性: CAN,EBI/EMI,SCI,SPI
外围设备: POR,PWM,WDT
输入/输出数: 32
程序存储器容量: 136KB(68K x 16)
程序存储器类型: 闪存
RAM 容量: 6K x 16
电压 - 电源 (Vcc/Vdd): 3 V ~ 3.6 V
数据转换器: A/D 16x12b
振荡器型: 外部
工作温度: -40°C ~ 85°C
封装/外壳: 160-BGA
包装: 托盘
56F807 Technical Data Technical Data, Rev. 16
56
Freescale Semiconductor
Measure the thermal resistance from the junction to where the leads are attached to the case. This definition
is approximately equal to a junction to board thermal resistance.
Use the value obtained by the equation (TJ – TT)/PD where TT is the temperature of the package case
determined by a thermocouple.
The thermal characterization parameter is measured per JESD51-2 specification using a 40-gauge type T
thermocouple epoxied to the top center of the package case. The thermocouple should be positioned so
that the thermocouple junction rests on the package. A small amount of epoxy is placed over the
thermocouple junction and over about 1mm of wire extending from the junction. The thermocouple wire
is placed flat against the package case to avoid measurement errors caused by cooling effects of the
thermocouple wire.
When heat sink is used, the junction temperature is determined from a thermocouple inserted at the
interface between the case of the package and the interface material. A clearance slot or hole is normally
required in the heat sink. Minimizing the size of the clearance is important to minimize the change in
thermal performance caused by removing part of the thermal interface to the heat sink. Because of the
experimental difficulties with this technique, many engineers measure the heat sink temperature and then
back-calculate the case temperature using a separate measurement of the thermal resistance of the
interface. From this case temperature, the junction temperature is determined from the junction-to-case
thermal resistance.
5.2 Electrical Design Considerations
Use the following list of considerations to assure correct operation:
Provide a low-impedance path from the board power supply to each VDD pin on the controller, and from the
board ground to each VSS pin.
The minimum bypass requirement is to place 0.1
μF capacitors positioned as close as possible to the
package supply pins. The recommended bypass configuration is to place one bypass capacitor on each of
the VDD/VSS pairs, including VDDA/VSSA. Ceramic and tantalum capacitors tend to provide better
performance tolerances.
CAUTION
This device contains protective circuitry to guard
against damage due to high static voltage or electrical
fields. However, normal precautions are advised to
avoid application of any voltages higher than maximum
rated voltages to this high-impedance circuit. Reliability
of operation is enhanced if unused inputs are tied to an
appropriate voltage level.
相关PDF资料
PDF描述
VI-B20-IW-B1 CONVERTER MOD DC/DC 5V 100W
MC9328MXLCVM15 IC MCU I.MXL 150MHZ 256-MAPBGA
VI-2NX-CU-S CONVERTER MOD DC/DC 5.2V 200W
CS42L51-CNZR IC CODEC LOW-V 24BIT 32-QFP
VI-2NW-CU-S CONVERTER MOD DC/DC 5.5V 200W
相关代理商/技术参数
参数描述
DSP56F807VF80E 功能描述:数字信号处理器和控制器 - DSP, DSC 16 BIT HYBRID CONTROLLER RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
DSP56F807VF80E 制造商:Freescale Semiconductor 功能描述:Digital Signal Processor IC
DSP56F807VF80J 制造商:Freescale Semiconductor 功能描述:DSP 16BIT - Trays
DSP56F826 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:16-bit Digital Signal Controllers
DSP56F826-827UM 制造商:未知厂家 制造商全称:未知厂家 功能描述:16-Bit Digital Signal Processor Users Manual