收藏本站
参数资料
型号： DSPIC30F3014-20I/PT
厂商： Microchip Technology
文件页数： 109/153页
文件大小： 0K
描述： IC DSPIC MCU/DSP 24K 44TQFP
产品培训模块： Serial Communications using dsPIC30F I2C
Serial Communications using dsPIC30F SPI
Serial Communications using dsPIC30F UART
dsPIC30F 12 bit ADC - Part 2
dsPIC30F Addressing Modes - Part 1
dsPIC30F Architecture - Part 1
dsPIC30F DSP Engine & ALU
dsPIC30F Interrupts
dsPIC30F Motor Control PWM
dsPIC Timers
Asynchronous Stimulus
dsPIC30F Addressing Modes - Part 2
dsPIC30F Architecture - Part 2
dsPIC30F 12-bit ADC Part 1
标准包装： 160
系列： dsPIC™ 30F
核心处理器： dsPIC
芯体尺寸： 16-位
速度： 20 MIPS
连通性： I²C，SPI，UART/USART
外围设备： 欠压检测/复位，POR，PWM，WDT
输入/输出数： 30
程序存储器容量： 24KB（8K x 24）
程序存储器类型： 闪存
EEPROM 大小： 1K x 8
RAM 容量： 2K x 8
电压 - 电源 (Vcc/Vdd)： 2.5 V ~ 5.5 V
数据转换器： A/D 13x12b
振荡器型： 内部
工作温度： -40°C ~ 85°C
封装/外壳： 44-TQFP
包装： 托盘
配用： XLT80PT3-ND - SOCKET TRAN ICE 80MQFP/TQFP
AC164305-ND - MODULE SKT FOR PM3 44TQFP
其它名称： DSPIC30F301420IPT
2010 Microchip Technology Inc.
DS70138G-page 59
dsPIC30F3014/4013
8.0
INTERRUPTS
The dsPIC30F sensor and general purpose families
have up to 41 interrupt sources and 4 processor excep-
tions (traps) which must be arbitrated based on a
priority scheme.
The CPU is responsible for reading the Interrupt Vector
Table (IVT) and transferring the address contained in
the interrupt vector to the program counter. The inter-
rupt vector is transferred from the program data bus
into the program counter via a 24-bit wide multiplexer
on the input of the program counter.
The Interrupt Vector Table (IVT) and Alternate Interrupt
Vector Table (AIVT) are placed near the beginning of
program memory (0x000004). The IVT and AIVT are
shown in Figure 8-1.
The
interrupt
controller
is
responsible
for
pre-
processing the interrupts and processor exceptions
prior to them being presented to the processor core.
The peripheral interrupts and traps are enabled,
prioritized and controlled using centralized Special
Function Registers:
IFS0<15:0>, IFS1<15:0>, IFS2<15:0>
All interrupt request flags are maintained in these
three registers. The flags are set by their respec-
tive peripherals or external signals and they are
cleared via software.
IEC0<15:0>, IEC1<15:0>, IEC2<15:0>
All interrupt enable control bits are maintained in
these three registers. These control bits are used
to individually enable interrupts from the
peripherals or external signals.
IPC0<15:0>... IPC10<7:0>
The user-assignable priority level associated with
each of these 41 interrupts is held centrally in
these eleven registers.
IPL<3:0>
The current CPU priority level is explicitly stored
in the IPL bits. IPL<3> is present in the CORCON
register, whereas IPL<2:0> are present in the
STATUS register (SR) in the processor core.
INTCON1<15:0>, INTCON2<15:0>
Global interrupt control functions are derived from
these two registers. INTCON1 contains the con-
trol and status flags for the processor exceptions.
The INTCON2 register controls the external
interrupt request signal behavior and the use of
the alternate vector table.
All interrupt sources can be user-assigned to one of
7 priority levels, 1 through 7, via the IPCx registers.
Each interrupt source is associated with an interrupt
vector, as shown in Table 8-1. Levels 7 and 1 represent
the
highest
and
lowest
maskable
priorities,
respectively.
If the NSTDIS bit (INTCON1<15>) is set, nesting of
interrupts is prevented. Thus, if an interrupt is currently
being serviced, processing of a new interrupt is pre-
vented even if the new interrupt is of higher priority than
the one currently being serviced.
Certain interrupts have specialized control bits for
features like edge or level triggered interrupts, inter-
rupt-on-change, etc. Control of these features remains
within the peripheral module which generates the
interrupt.
The DISI instruction can be used to disable the
processing of interrupts of priorities 6 and lower for a
certain number of instructions, during which the DISI bit
(INTCON2<14>) remains set.
When an interrupt is serviced, the PC is loaded with the
address stored in the vector location in program
memory that corresponds to the interrupt. There are
63 different vectors within the IVT (refer to Table 8-1)
These vectors are contained in locations 0x000004
through 0x0000FE of program memory (refer to
Table 8-1). These locations contain 24-bit addresses.
In order to preserve robustness, an address error trap
takes place should the PC attempt to fetch any of these
words during normal execution. This prevents execu-
tion of random data as a result of accidentally
decrementing a PC into vector space, accidentally
mapping a data space address into vector space or the
PC rolling over to 0x000000 after reaching the end of
implemented program memory space. Execution of a
GOTO
instruction to this vector space also generates an
address error trap.
Note:
This data sheet summarizes features of
this group of dsPIC30F devices and is not
intended to be a complete reference
source. For more information on the CPU,
peripherals,
register
descriptions
and
general device functionality, refer to the
“dsPIC30F Family Reference Manual”
(DS70046). For more information on the
device instruction set and programming,
refer to the “16-bit MCU and DSC Pro-
grammer’s
Reference
Manual”
(DS70157).
Note:
Interrupt flag bits get set when an interrupt
condition occurs, regardless of the state of
its corresponding enable bit. User soft-
ware should ensure the appropriate inter-
rupt flag bits are clear prior to enabling an
interrupt.
Note:
Assigning a priority level of ‘0’ to an inter-
rupt source is equivalent to disabling that
interrupt.
Note:
The IPL bits become read-only whenever
the NSTDIS bit has been set to ‘1’.
相关PDF资料
PDF描述
ATMEGA325V-8MI IC AVR MCU 32K 8MHZ 64-QFN
PIC16F74-I/P IC MCU FLASH 4KX14 A/D 40DIP
ATMEGA165-16AI IC AVR MCU 16K 16MHZ 64TQFP
ATMEGA165-16AU IC AVR MCU 16K 16MHZ 64TQFP
ATMEGA165V-8MU IC AVR MCU 16K 8MHZ 64-QFN
相关代理商/技术参数
参数描述
DSPIC30F3014-30I/ML 功能描述:数字信号处理器和控制器 - DSP, DSC General Purpose RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
DSPIC30F3014-30I/P 功能描述:数字信号处理器和控制器 - DSP, DSC General Purpose RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
DSPIC30F3014-30I/P 制造商:Microchip Technology Inc 功能描述:16- Bit Digital Signal Controller
DSPIC30F3014-30I/PT 功能描述:数字信号处理器和控制器 - DSP, DSC General Purpose RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
dsPIC30F3014T-20E/ML 功能描述:数字信号处理器和控制器 - DSP, DSC 44LD 20MIPS 24 KB RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*