- 您现在的位置：买卖IC网 > PDF目录11256 > DSPIC30F5016-30I/PT (Microchip Technology)IC DSPIC MCU/DSP 66K 80TQFP PDF资料下载
参数资料
| 型号： | DSPIC30F5016-30I/PT |
| 厂商： | Microchip Technology |
| 文件页数： | 99/129页 |
| 文件大小： | 0K |
| 描述： | IC DSPIC MCU/DSP 66K 80TQFP |
| 产品培训模块： | dsPIC30F Quadrature Encoder Interface Serial Communications using dsPIC30F CAN Serial Communications using dsPIC30F I2C Serial Communications using dsPIC30F SPI Serial Communications using dsPIC30F UART dsPIC30F 12 bit ADC - Part 2 dsPIC30F Addressing Modes - Part 1 dsPIC30F Architecture - Part 1 dsPIC30F DSP Engine & ALU Asynchronous Stimulus dsPIC30F Addressing Modes - Part 2 dsPIC30F Architecture - Part 2 dsPIC30F 12-bit ADC Part 1 |
| 标准包装： | 119 |
| 系列： | dsPIC™ 30F |
| 核心处理器： | dsPIC |
| 芯体尺寸： | 16-位 |
| 速度： | 30 MIP |
| 连通性： | CAN，I²C，SPI，UART/USART |
| 外围设备： | 高级欠压探测/复位，电机控制 PWM，QEI，POR，PWM，WDT |
| 输入/输出数： | 68 |
| 程序存储器容量： | 66KB（22K x 24） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 1K x 8 |
| RAM 容量： | 2K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.5 V ~ 5.5 V |
| 数据转换器： | A/D 16x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 80-TQFP |
| 包装： | 托盘 |
| 产品目录页面： | 651 (CN2011-ZH PDF) |
| 配用： | AC164320-ND - MODULE SKT MPLAB PM3 80TQFP AC30F007-ND - MODULE SKT FOR DSPIC30F 80TQFP DV164005-ND - KIT ICD2 SIMPLE SUIT W/USB CABLE |
| 其它名称： | DSPIC30F501630IPT |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页当前第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页
2008 Microchip Technology Inc.
DS70149D-page 71
dsPIC30F5015/5016
10.0 TIMER2/3 MODULE
This section describes the 32-bit General Purpose
(GP) timer module (Timer2/3) and associated
operational modes. Figure 10-1 depicts the simplified
block diagram of the 32-bit Timer2/3 module.
Figure 10-2 and Figure 10-3 show Timer2/3 configured
as two independent 16-bit timers: Timer2 and Timer3,
respectively.
The Timer2/3 module is a 32-bit timer, which can be
configured as two 16-bit timers, with selectable
operating modes. These timers are utilized by other
peripheral modules such as:
Input Capture
Output Compare/Simple PWM
The following sections provide a detailed description,
including setup and control registers, along with
associated block diagrams for the operational modes of
the timers.
The 32-bit timer has the following modes:
Two independent 16-bit timers (Timer2 and
Timer3) with all 16-bit operating modes (except
Asynchronous Counter mode)
Single 32-bit Timer operation
Single 32-bit Synchronous Counter
Further, the following operational characteristics are
supported:
ADC Event Trigger
Timer Gate Operation
Selectable Prescaler Settings
Timer Operation during Idle and Sleep modes
Interrupt on a 32-bit Period register Match
These operating modes are determined by setting the
appropriate bit(s) in the 16-bit T2CON and T3CON
SFRs.
For 32-bit timer/counter operation, Timer2 is the least
significant word and Timer3 is the most significant word
of the 32-bit timer.
16-bit Mode: In 16-bit mode, Timer2 and Timer3 can be
configured as two independent 16-bit timers. Each timer
can be set up in either 16-bit Timer mode or 16-bit
Synchronous Counter mode. See Section 9.0 “Timer1
Module” for details on these two operating modes.
The only functional difference between Timer2 and
Timer3 is that Timer2 provides synchronization of the
clock prescaler output. This is useful for high-frequency
external clock inputs.
32-bit Timer Mode: In the 32-bit Timer mode, the timer
increments on every instruction cycle up to a match
value, preloaded into the combined 32-bit Period
register, PR3/PR2, then resets to ‘0’ and continues to
count.
For synchronous 32-bit reads of the Timer2/Timer3
pair, reading the least significant word (TMR2 register)
will cause the most significant word to be read and
latched into a 16-bit holding register, termed
TMR3HLD.
For synchronous 32-bit writes, the holding register
(TMR3HLD) must first be written to. When followed by
a write to the TMR2 register, the contents of TMR3HLD
will be transferred and latched into the MSB of the
32-bit timer (TMR3).
32-bit Synchronous Counter Mode: In the 32-bit
Synchronous Counter mode, the timer increments on
the rising edge of the applied external clock signal,
which is synchronized with the internal phase clocks.
The timer counts up to a match value preloaded in the
combined 32-bit Period register, PR3/PR2, then resets
to ‘0’ and continues.
When the timer is configured for the Synchronous
Counter mode of operation and the CPU goes into the
Idle mode, the timer will stop incrementing, unless the
TSIDL (T2CON<13>) bit = 0. If TSIDL = 1, the timer
module logic will resume the incrementing sequence
upon termination of the CPU Idle mode.
Note:
This data sheet summarizes features of
this group of dsPIC30F devices and is not
intended to be a complete reference
source. For more information on the CPU,
peripherals, register descriptions and
general device functionality, refer to the
“dsPIC30F Family Reference Manual”
(DS70046). For more information on the
device instruction set and programming,
refer to the “dsPIC30F/33F Programmer’s
Reference Manual” (DS70157).
Note:
Timer2 is a Type B timer and Timer3 is a
Type C timer. Please refer to the
appropriate timer type in Section 24.0
of
this
document.
Note:
For 32-bit timer operation, T3CON control
bits are ignored. Only T2CON control bits
are used for setup and control. Timer2
clock and gate inputs are utilized for the
32-bit timer module, but an interrupt is
generated with the Timer3 Interrupt Flag
(T3IF) and the interrupt is enabled with the
Timer3 Interrupt Enable bit (T3IE).
相关PDF资料 |
PDF描述 |
|---|---|
| VI-J5R-IX-F3 | CONVERTER MOD DC/DC 7.5V 75W |
| ADG741BKSZ5-REEL7 | IC SWITCH SPST SC70-5 |
| ADG742BKSZ-REEL7 | IC SWITCH SPST SC70-6 |
| ADG3249BRJ-REEL7 | IC MUX/DEMUX 2X1 SOT23-8 |
| ADG742BKSZ5-REEL | IC SWITCH SPST SC70-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| dsPIC30F5016T-20E/PT | 功能描述:数字信号处理器和控制器 - DSP, DSC 20MIPS 66 KB RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| DSPIC30F5016T-20I/PT | 功能描述:IC DSPIC MCU/DSP 66K 80TQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:dsPIC™ 30F 产品培训模块:XLP Deep Sleep Mode 8-bit PIC® Microcontroller Portfolio 标准包装:22 系列:PIC® XLP™ 18F 核心处理器:PIC 芯体尺寸:8-位 速度:48MHz 连通性:I²C，SPI，UART/USART，USB 外围设备:欠压检测/复位，POR，PWM，WDT 输入/输出数:14 程序存储器容量:8KB（4K x 16） 程序存储器类型:闪存 EEPROM 大小:256 x 8 RAM 容量:512 x 8 电压 - 电源 (Vcc/Vdd):1.8 V ~ 5.5 V 数据转换器:A/D 11x10b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:20-DIP（0.300"，7.62mm） 包装:管件 产品目录页面:642 (CN2011-ZH PDF) 配用:DV164126-ND - KIT DEVELOPMENT USB W/PICKIT 2DM164127-ND - KIT DEVELOPMENT USB 18F14/13K50AC164112-ND - VOLTAGE LIMITER MPLAB ICD2 VPP |
| dsPIC30F5016T-30I/PT | 功能描述:数字信号处理器和控制器 - DSP, DSC 30MIPS 66 KB RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| DSPIC30F6010-20E/PF | 功能描述:数字信号处理器和控制器 - DSP, DSC 30MHz 66KB Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| DSPIC30F6010-20I/PF | 功能描述:数字信号处理器和控制器 - DSP, DSC 20MHz 144KB Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。