收藏本站
参数资料
型号： DSPIC33FJ128GP202-I/SP
厂商： Microchip Technology
文件页数： 61/73页
文件大小： 0K
描述： IC DSPIC MCU/DSP 128K 28DIP
特色产品： PIC24FJ/33FJ MCUs & dsPIC? DSCs
标准包装： 15
系列： dsPIC™ 33F
核心处理器： dsPIC
芯体尺寸： 16-位
速度： 40 MIP
连通性： I²C，IrDA，LIN，SPI，UART/USART
外围设备： AC'97，欠压检测/复位，DMA，I²S，POR，PWM，WDT
输入/输出数： 21
程序存储器容量： 128KB（128K x 8）
程序存储器类型： 闪存
RAM 容量： 8K x 8
电压 - 电源 (Vcc/Vdd)： 3 V ~ 3.6 V
数据转换器： A/D 10x10b/12b
振荡器型： 内部
工作温度： -40°C ~ 85°C
封装/外壳： 28-DIP（0.300"，7.62mm）
包装： 管件
产品目录页面： 653 (CN2011-ZH PDF)
配用： MA330019-ND - PIM DSPIC33F MC 44P-100P QFN
DV164033-ND - KIT START EXPLORER 16 MPLAB ICD2
DV164005-ND - KIT ICD2 SIMPLE SUIT W/USB CABLE
dsPIC33FJ32GP302/304, dsPIC33FJ64GPX02/X04, AND dsPIC33FJ128GPX02/X04
DS70292G-page 64
2007-2012 Microchip Technology Inc.
4.6.3
MODULO ADDRESSING
APPLICABILITY
Modulo Addressing can be applied to the Effective
Address (EA) calculation associated with any W
register. Address boundaries check for addresses
equal to:
The upper boundary addresses for incrementing
buffers
The lower boundary addresses for decrementing
buffers
It is important to realize that the address boundaries
check for addresses less than or greater than the upper
(for incrementing buffers) and lower (for decrementing
buffers) boundary addresses (not just equal to).
Address changes can, therefore, jump beyond
boundaries and still be adjusted correctly.
4.7
Bit-Reversed Addressing
Bit-Reversed Addressing mode is intended to simplify
data reordering for radix-2 FFT algorithms. It is
supported by the X AGU for data writes only.
The modifier, which can be a constant value or register
contents, is regarded as having its bit order reversed.
The address source and destination are kept in normal
order. Thus, the only operand requiring reversal is the
modifier.
4.7.1
BIT-REVERSED ADDRESSING
IMPLEMENTATION
Bit-Reversed Addressing mode is enabled in any of
these situations:
BWM bits (W register selection) in the MODCON
register are any value other than ‘15’ (the stack
cannot be accessed using Bit-Reversed
Addressing)
The BREN bit is set in the XBREV register
The addressing mode used is Register Indirect
with Pre-Increment or Post-Increment
If the length of a bit-reversed buffer is M = 2N bytes,
the last ‘N’ bits of the data buffer start address must
be zeros.
XB<14:0> is the Bit-Reversed Address modifier, or
‘pivot point,’ which is typically a constant. In the case of
an FFT computation, its value is equal to half of the FFT
data buffer size.
When enabled, Bit-Reversed Addressing is executed
only for Register Indirect with Pre-Increment or Post-
Increment Addressing and word-sized data writes. It
does not function for any other addressing mode or for
byte-sized data, and normal addresses are generated
instead. When Bit-Reversed Addressing is active, the
W Address Pointer is always added to the address
modifier (XB), and the offset associated with the
Register Indirect Addressing mode is ignored. In
addition, as word-sized data is a requirement, the LSb
of the EA is ignored (and always clear).
If Bit-Reversed Addressing has already been enabled
by setting the BREN bit (XBREV<15>), a write to the
XBREV register should not be immediately followed by
an indirect read operation using the W register that has
been designated as the bit-reversed pointer.
Note:
The modulo corrected effective address is
written back to the register only when Pre-
Modify or Post-Modify Addressing mode is
used to compute the effective address.
When an address offset (such as [W7 +
W2]) is used, Modulo Address correction
is performed but the contents of the
register remain unchanged.
Note:
All bit-reversed EA calculations assume
word-sized data (LSb of every EA is
always clear). The XB value is scaled
accordingly to generate compatible (byte)
addresses.
Note:
Modulo Addressing and Bit-Reversed
Addressing
should
not
be
enabled
together. If an application attempts to do so,
Bit-Reversed Addressing assumes priority
when active for the X WAGU and X WAGU,
Modulo Addressing is disabled. However,
Modulo Addressing continues to function in
the X RAGU.
相关PDF资料
PDF描述
PIC24FJ128GA310-I/BG MCU 16BIT 128KB FLASH 121TFBGA
PIC24HJ128GP204-I/PT IC PIC MCU FLASH 128K 44TQFP
PIC18F8393-I/PT IC PIC MCU FLASH 4KX16 80TQFP
DSPIC33FJ128GP204-I/PT IC DSPIC MCU/DSP 128K 44TQFP
DSPIC33FJ64MC802-I/MM IC DSPIC MCU/DSP 64K 28-QFN
相关代理商/技术参数
参数描述
dsPIC33FJ128GP202T-I/MM 功能描述:数字信号处理器和控制器 - DSP, DSC 16B DSC 28LD128KB DMA 40MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
dsPIC33FJ128GP202T-I/SO 功能描述:数字信号处理器和控制器 - DSP, DSC 16B DSC 28LD128KB DMA 40MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
dsPIC33FJ128GP204-E/ML 功能描述:数字信号处理器和控制器 - DSP, DSC 16b DSC 128KB Flash DMA 40MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
dsPIC33FJ128GP204-E/PT 功能描述:数字信号处理器和控制器 - DSP, DSC 16b DSC 128KB Flash DMA 40MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
dsPIC33FJ128GP204-I/ML 功能描述:数字信号处理器和控制器 - DSP, DSC 16B DSC 44LD128KB DMA 40MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*