- 您现在的位置：买卖IC网 > PDF目录13590 > EL7564CMZ-T13 (Intersil)IC REG BUCK SYNC ADJ 4A 20SOIC PDF资料下载
参数资料
| 型号： | EL7564CMZ-T13 |
| 厂商： | Intersil |
| 文件页数： | 15/17页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 4A 20SOIC |
| 标准包装： | 1,000 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1 V ~ 3.8 V |
| 输入电压： | 4.5 V ~ 5.5 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 1MHz |
| 电流 - 输出： | 4A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SOIC（0.295"，7.50mm 宽） |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 20-SO |
EL7564
4. Start-up Delay
A capacitor can be added to the EN pin to delay the
converter start-up (Figure 26) by utilizing the pull-up current.
The delay time is approximately:
t d ( ms ) = 1200 × C ( μ F )
The EL7564CRE utilizes the 28-pin HTSSOP package. The
majority of heat is dissipated through the heat pad exposed
at the bottom of the package. Therefore, the heat pad needs
to be soldered to the PCB. The thermal resistance for this
package is as low as 29°C/W, better than that of SO20.
Typical performance is shown in the curves section. The
actual junction temperature can be measured at V TJ pin.
1
2
6
20
19
15
C
V OUT
Since the thermal performance of the IC is heavily
dependent on the board layout, the system designer should
exercise care during the design phase to ensure that the IC
will operate under the worst-case environmental conditions.
7
EL7564
14
Layout Considerations
8
13
V IN
The layout is very important for the converter to function
9
10
STP
STN
+
-
12
11
t d
V O
properly. Power Ground ( ) and Signal Ground ( ) should
be separated to ensure that the high pulse current in the
Power Ground never interferes with the sensitive signals
TIME
FIGURE 28. START-UP DELAY
Thermal Management
The EL7564CM utilizes “fused lead” packaging technology in
conjunction with the system board layout to achieve a lower
thermal resistance than typically found in standard SO20
packages. By fusing (or connecting) multiple external leads
to the die substrate within the package, a very conductive
heat path is created to the outside of the package. This
conductive heat path MUST then be connected to a heat
sinking area on the PCB in order to dissipate heat out and
away from the device. The conductive paths for the
EL7564CM package are the fused leads: # 6, 7, 11, 12, and
13. If a sufficient amount of PCB metal area is connected to
the fused package leads, a junction-to-ambient resistance of
43°C/W can be achieved (compared to 85°C/W for a
standard SO20 package). The general relationship between
PCB heat-sinking metal area and the thermal resistance for
this package is shown in the Performance Curves section of
this data sheet. It can be readily seen that the thermal
resistance for this package approaches an asymptotic value
of approximately 43°C/W without any airflow, and 33°C/W
with 100 LFPM airflow. Additional information can be found
in Application Note #8 (Measuring the Thermal Resistance
of Power Surface-Mount Packages). For a thermal shutdown
die junction temperature of 135°C, and power dissipation of
1.5W, the ambient temperature can be as high as 70°C
without airflow. With 100 LFPM airflow, the ambient
temperature can be extended to 85°C.
15
connected to Signal Ground. They should only be connected
at one point (normally at the negative side of either the input
or output capacitor.)
The trace connected to the FB pin is the most sensitive
trace. It needs to be as short as possible and in a “quiet”
place, preferably with the PGND or SGND traces
surrounding it.
In addition, the bypass capacitor connected to the V DD pin
needs to be as close to the pin as possible.
The heat of the chip is mainly dissipated through the PGND
pins for the CM package, and through the heat pad at the
bottom for the CRE package. Maximizing the copper area
around these PGND pins or the heat pad is preferable. In
addition, a solid ground plane is always helpful for the EMI
performance.
The demo board is a good example of layout based on these
principles. Please refer to the EL7564 Application Brief for
the layout.
FN7297.3
May 9, 2005
相关PDF资料 |
PDF描述 |
|---|---|
| EL7564CREZ-T7 | IC REG BUCK SYNC ADJ 4A 28HTSSOP |
| VE-24J-EX-F4 | CONVERTER MOD DC/DC 36V 75W |
| VE-24J-EX-F3 | CONVERTER MOD DC/DC 36V 75W |
| MAX6794TPLD4+T | IC REG LIN W/SPR VSR 20-TQFN |
| VE-24J-EX-F2 | CONVERTER MOD DC/DC 36V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EL7564CRE | 功能描述:IC REG BUCK SYNC ADJ 4A 28HTSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:3.3V 输入电压:4.5 V ~ 24 V PWM 型:- 频率 - 开关:- 电流 - 输出:125mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 包装:Digi-Reel® 供应商设备封装:SOT-6 其它名称:MAX1836EUT33#TG16DKR |
| EL7564CRE-T13 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Monolithic 4 Amp DC/DC Step-Down Regulator |
| EL7564CRE-T7 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Monolithic 4 Amp DC/DC Step-Down Regulator |
| EL7564CREZ | 功能描述:直流/直流开关调节器 EL7564CREZ MONO 4 AMP STP DWN SWITCH RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| EL7564CREZ-T13 | 功能描述:直流/直流开关调节器 EL7564CREZ MONO 4 AMP STP DWN SWTCH RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
发布紧急采购，3分钟左右您将得到回复。