- 您现在的位置：买卖IC网 > PDF目录18758 > EM260-RTR (Silicon Laboratories Inc)IC ZIGBEE SYSTEM-ON-CHIP 40-QFN PDF资料下载
参数资料
| 型号： | EM260-RTR |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 16/50页 |
| 文件大小： | 0K |
| 描述： | IC ZIGBEE SYSTEM-ON-CHIP 40-QFN |
| 标准包装： | 1 |
| 频率： | 2.4GHz |
| 数据传输率 - 最大： | 250kbps |
| 调制或协议： | 802.15.4 |
| 应用： | ZigBee? |
| 功率 - 输出： | -32dBm ~ 3dBm |
| 灵敏度： | -97dBm |
| 电源电压： | 2.1 V ~ 3.6 V |
| 电流 - 接收： | 30mA |
| 电流 - 传输： | 34mA |
| 数据接口： | PCB，表面贴装 |
| 天线连接器： | PCB，表面贴装 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 40-VFQFN 裸露焊盘 |
| 包装： | 标准包装 |
| 配用： | 636-1009-ND - PROGRAMMER USB FLASH EM250/260 |
| 其它名称： | 636-1007-6 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页
EM260
seen in range testing measurements when nodes are closely positioned and transmitting at high power or when
receiving from test equipment. There is no damage to the EM260 from this problem. This issue will rarely
occur in the field as ZigBee Nodes will be spaced far enough apart. If nodes are close enough for it to occur in
the field, the MAC and networking software treat the packet as not having been received and therefore the
MAC level and network level retries resolve the problem without needing to notify the upper level application.
4.2
Transmit (TX) Path
The EM260 transmitter utilizes both analog circuitry and digital logic to produce the O-QPSK modulated signal.
The area-efficient TX architecture directly modulates the spread symbols prior to transmission. The
differential signal paths increase noise immunity and provide a common interface for the external balun.
4.2.1
TX Baseband
The EM260 TX baseband (within the digital domain) performs the spreading of the 4-bit symbol into its IEEE
802.15.4-2003-defined 32-chip I and Q sequence. In addition, it provides the interface for software to perform
the calibration of the TX module in order to reduce process, temperature, and voltage variations.
4.2.2
TX_ACTIVE Signal
Even though the EM260 provides an output power suitable for most ZigBee applications, some applications will
require an external power amplifier (PA). Due to the timing requirements of IEEE 802.15.4-2003, the EM260
provides a signal, TX_ACTIVE, to be used for external PA power management and RF Switching logic. When in
TX, the TX Baseband drives TX_ACTIVE high (as described in Table 6). When in RX, the TX_ACTIVE signal is
low. If an external PA is not required, then the TX_ACTIVE signal should be connected to GND through a 100k
Ohm resistor, as shown in the application circuit in Figure 14.
The TX_ACTIVE signal can only source 1mA of current, and it is based upon the 1.8V signal swing. If the PA
Control logic requires greater current or voltage potential, then TX_ACTIVE should be buffered externally to
the EM260.
4.3
Integrated MAC Module
The EM260 integrates critical portions of the IEEE 802.15.4-2003 MAC requirements in hardware. This allows
the EM260 to provide greater bandwidth to application and network operations. In addition, the hardware acts
as a first-line filter for non-intended packets. The EM260 MAC utilizes a DMA interface to RAM memory to
further reduce the overall microcontroller interaction when transmitting or receiving packets.
When a packet is ready for transmission, the software configures the TX MAC DMA by indicating the packet
buffer RAM location. The MAC waits for the backoff period, then transitions the baseband to TX mode and
performs channel assessment. When the channel is clear, the MAC reads data from the RAM buffer, calculates
the CRC, and provides 4-bit symbols to the baseband. When the final byte has been read and sent to the
baseband, the CRC remainder is read and transmitted.
The MAC resides in RX mode most of the time, and different format and address filters keep non-intended
packets from using excessive RAM buffers, as well as preventing the EM260 CPU from being interrupted. When
the reception of a packet begins, the MAC reads 4-bit symbols from the baseband and calculates the CRC. It
assembles the received data for storage in a RAM buffer. A RX MAC DMA provides direct access to the RAM
memory. Once the packet has been received, additional data is appended to the end of the packet in the RAM
buffer space. The appended data provides statistical information on the packet for the software stack.
The primary features of the MAC are:
120-0260-000M Rev 1.1
?
?
?
?
CRC generation, appending, and checking
Hardware timers and interrupts to achieve the MAC symbol timing
Automatic preamble, and SFD pre-pended to a TX packet
Address recognition and packet filtering on received packets
Page 16
相关PDF资料 |
PDF描述 |
|---|---|
| MD7IC18120GNR1 | IC PWR AMP RF LDMOS TO270-16 |
| TRC105 | IC TXRX 300MHZ-510MHZ 32TQFN |
| MT-6-15 | XFRMR 115V 5V 1.75A 6VA 3OUT |
| IF-2-10 | XFRMR 115/230V 5V 400MA 2VA PCB |
| 14A-20-515 | XFRMR PWR 115/230V 5V 750MA 20VA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EM260-RTY | 功能描述:IC ZIGBEE SYSTEM-ON-CHIP 40-QFN RoHS:是 类别:RF/IF 和 RFID >> RF 收发器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:30 系列:- 频率:4.9GHz ~ 5.9GHz 数据传输率 - 最大:54Mbps 调制或协议:* 应用:* 功率 - 输出:-3dBm 灵敏度:- 电源电压:2.7 V ~ 3.6 V 电流 - 接收:* 电流 - 传输:* 数据接口:PCB，表面贴装 存储容量:- 天线连接器:PCB，表面贴装 工作温度:-25°C ~ 85°C 封装/外壳:68-TQFN 裸露焊盘 包装:管件 |
| EM260-USART-JMP-R | 功能描述:KIT JUMP START FOR EM260 RoHS:否 类别:RF/IF 和 RFID >> RF 评估和开发套件，板 系列:JumpStart 标准包装:1 系列:- 类型:GPS 接收器 频率:1575MHz 适用于相关产品:- 已供物品:模块 其它名称:SER3796 |
| EM2630-12# | 制造商:Fluke Electronics 功能描述:BNC (F) TO ALLIGATOR CLIPS 12 INCHES 制造商:Pomona Electronics 功能描述: |
| EM-26392-C36 | 功能描述:麦克风 3.61 X 3.61 X 2.21MM -51 SENS, 12SL PORT RoHS:否 制造商:Knowles Acoustics 方向性:Omnidirectional 阻抗:4.4 K Ohms 工作电压:0.9 V to 10 V 灵敏度:- 53 dB 端接类型:Wire Leads 长度:5.56 mm 宽度:3.98 mm 深度:2.21 mm |
| EM-26596-C36 | 功能描述:麦克风 3.61 X 3.61 X 2.21MM -52 SENS, 12B PORT RoHS:否 制造商:Knowles Acoustics 方向性:Omnidirectional 阻抗:4.4 K Ohms 工作电压:0.9 V to 10 V 灵敏度:- 53 dB 端接类型:Wire Leads 长度:5.56 mm 宽度:3.98 mm 深度:2.21 mm |
发布紧急采购，3分钟左右您将得到回复。