参数资料
型号: EM773FHN33,551
厂商: NXP Semiconductors
文件页数: 50/51页
文件大小: 0K
描述: IC ENERGY METER ARM 32VQFN
其它有关文件: EM773 Energy Metering IC Training
特色产品: EM773 Energy Metering IC
标准包装: 260
核心处理器: ARM? Cortex?-M0
芯体尺寸: 32-位
速度: 48MHz
连通性: I²C,SPI,UART/USART
外围设备: 欠压检测/复位,POR,WDT
输入/输出数: 25
程序存储器容量: 32KB(32K x 8)
程序存储器类型: 闪存
RAM 容量: 8K x 8
电压 - 电源 (Vcc/Vdd): 1.8 V ~ 3.6 V
振荡器型: 内部
工作温度: -40°C ~ 85°C
封装/外壳: 32-VQFN 裸露焊盘
包装: 托盘
配用: 568-6681-ND - BOARD EVAL EM773 METER EU PLUG
568-6680-ND - BOARD EVAL EM773 METER US PLUG
其它名称: 568-5213
EM773
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2012. All rights reserved.
Product data sheet
Rev. 2 — 3 January 2012
8 of 51
NXP Semiconductors
EM773
Energy metering IC
[1]
Pin state at reset for default function: I = Input; O = Output; PU = internal pull-up enabled; (pins pulled up to full VDD level ); IA = inactive,
no pull-up/down enabled.
[2]
See Figure 25 for the reset pad configuration. RESET functionality is not available in Deep power-down mode. Use the WAKEUP pin to
reset the chip and wake up from Deep power-down mode. An external pull-up resistor is required on this pin for the Deep power-down
mode. Pin is 5 V tolerant.
[3]
5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors and configurable hysteresis (see Figure 24).
[4]
I2C-bus pads compliant with the I2C-bus specification for I2C standard mode and I2C Fast-mode Plus.
[5]
5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors, configurable hysteresis, and analog input.
When configured as a analog input, digital section of the pad is disabled and the pin is not 5 V tolerant (see Figure 24).
[6]
When the system oscillator is not used, connect XTALIN and XTALOUT as follows: XTALIN can be left floating or can be grounded
(grounding is preferred to reduce susceptibility to noise). XTALOUT should be left floating.
PIO1_11
27
no
I/O
I;PU
PIO1_11 — General purpose digital input/output pin.
PIO2_0
I/O
Port 2 — Port 2 is a 12-bit I/O port with individual
direction and function controls for each bit. The
operation of port 2 pins depends on the function
selected through the IOCONFIG register block. Pins
PIO2_1 to PIO2_11 are not available.
PIO2_0/DTR
no
I/O
I;PU
PIO2_0 — General purpose digital input/output pin.
O-
DTR — Data Terminal Ready output for UART.
PIO3_0 to PIO3_5
no
I/O
Port 3 — Port 3 is a 12-bit I/O port with individual
direction and function controls for each bit. The
operation of port 3 pins depends on the function
selected through the IOCONFIG register block. Pins
PIO3_0, PIO3_1, PIO3_3 and PIO3_6 to PIO3_11 are
not available.
PIO3_2
no
I/O
I;PU
PIO3_2 — General purpose digital input/output pin.
PIO3_4
no
I/O
I;PU
PIO3_4 — General purpose digital input/output pin.
PIO3_5
no
I/O
I;PU
PIO3_5 — General purpose digital input/output pin.
VDD
6; 29
-
I
-
3.3 V supply voltage to the internal regulator, the
external rail, and the metrology engine.
XTALIN
-
I
-
Input to the oscillator circuit and internal clock generator
circuits. Input voltage must not exceed 1.8 V.
XTALOUT
-
O
-
Output from the oscillator amplifier.
VSS
33
-
Thermal pad. Connect to ground.
Table 2.
EM773 pin description table …continued
Symbol
Pin
Start
logic
input
Type
Reset
state
[1]
Description
相关PDF资料
PDF描述
ENC28J60T/SO IC ETHERNET CTRLR W/SPI 28SOIC
ENC624J600T-I/PT IC ETHERNET CTRLR W/SPI 64-TQFP
EP1AGX90EF1152I6 IC ARRIA GX FPGA 90K 1152FBGA
EP1C3T144A8N IC CYCLONE FPGA 2910 LE 144-TQFP
EP1K100FC484-1N IC ACEX 1K FPGA 100K 484-FBGA
相关代理商/技术参数
参数描述
EM77565 制造商:EMC 制造商全称:ELAN Microelectronics Corp 功能描述:ADPCM WITH PCM CODEC
EM77930 制造商:EMC 制造商全称:ELAN Microelectronics Corp 功能描述:USB + BB Controller
EM77950 制造商:EMC 制造商全称:ELAN Microelectronics Corp 功能描述:BB Controller
EM77F900 制造商:EMC 制造商全称:ELAN Microelectronics Corp 功能描述:USB HUB+BB Controller
EM780FP16AS-45LF 制造商:EMLSI 制造商全称:Emerging Memory & Logic Solutions Inc 功能描述:64K x16 bit Super Low Power and Low Voltage Full CMOS Static RAM