收藏本站
参数资料
型号： ENC424J600T-I/ML
厂商： Microchip Technology
文件页数： 129/168页
文件大小： 0K
描述： IC ETHERNET CTRLR W/SPI 44-QFN
视频文件： Fast 100 Mbps Ethernet PICtail Plus Overview
标准包装： 1,600
控制器类型： 以太网控制器（IEEE 802.3）
接口： SPI
电源电压： 3 V ~ 3.6 V
电流 - 电源： 96mA
工作温度： -40°C ~ 85°C
安装类型： 表面贴装
封装/外壳： 44-VQFN 裸露焊盘
供应商设备封装： 44-QFN（8x8）
包装： 带卷 (TR)
配用： AC164132-ND - BOARD DAUGHTER PICTAIL ETHERNET
2007 Microchip Technology Inc.
DS21993C-page 61
PIC16CR7X
REGISTER 9-2:
SSPCON: SYNC SERIAL PORT CONTROL (ADDRESS 14h)
R/W-0
WCOL
SSPOV
SSPEN
CKP
SSPM3
SSPM2
SSPM1
SSPM0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
WCOL: Write Collision Detect bit
1
= The SSPBUF register is written while it is still transmitting the previous word
(must be cleared in software)
0
= No collision
bit 6
SSPOV: Receive Overflow Indicator bit
In SPI mode:
1
= A new byte is received while the SSPBUF register is still holding the previous data. In case
of overflow, the data in SSPSR is lost. Overflow can only occur in Slave mode. The user
must read the SSPBUF, even if only transmitting data, to avoid setting overflow. In
Master mode, the overflow bit is not set since each new reception (and transmission) is
initiated by writing to the SSPBUF register.
0
= No overflow
In I2C mode:
1
= A byte is received while the SSPBUF register is still holding the previous byte. SSPOV
is a “don’t care” in Transmit mode. SSPOV must be cleared in software in either mode.
0
= No overflow
bit 5
SSPEN: Synchronous Serial Port Enable bit
In SPI mode:
1
= Enables serial port and configures SCK, SDO and SDI as serial port pins
0
= Disables serial port and configures these pins as I/O port pins
In I2C mode:
1
= Enables the serial port and configures the SDA and SCL pins as serial port pins
0
= Disables serial port and configures these pins as I/O port pins
In both modes, when enabled, these pins must be properly configured as input or output.
bit 4
CKP: Clock Polarity Select bit
In SPI mode:
1
= Idle state for clock is a high level (Microwire default)
0
= Idle state for clock is a low level (Microwire alternate)
In I2C mode:
SCK release control
1
= Enable clock
0
= Holds clock low (clock stretch). (Used to ensure data setup time.)
bit 3-0
SSPM3:SSPM0: Synchronous Serial Port Mode Select bits
0000
= SPI Master mode, clock = FOSC/4
0001
= SPI Master mode, clock = FOSC/16
0010
= SPI Master mode, clock = FOSC/64
0011
= SPI Master mode, clock = TMR2 output/2
0100
= SPI Slave mode, clock = SCK pin. SS pin control enabled.
0101
= SPI Slave mode, clock = SCK pin. SS pin control disabled. SS can be used as I/O pin.
0110
= I2C Slave mode, 7-bit address
0111
= I2C Slave mode, 10-bit address
1011
= I2C Firmware Controlled Master mode (slave Idle)
1110
= I2C Slave mode, 7-bit address with Start and Stop bit interrupts enabled
1111
= I2C Slave mode, 10-bit address with Start and Stop bit interrupts enabled
相关PDF资料
PDF描述
PIC16F677-E/P IC PIC MCU FLASH 2KX14 20DIP
MCP2155-I/P IC IRDA PROTOCOL CTRLR 18DIP
MCP2150T-I/SS IC IRDA STD CONTROLLER 20SSOP
MCP2155T-I/SO IC IRDA PROTOCOL CONTRLR 18-SOIC
PIC18F25J10T-I/SS IC PIC MCU FLASH 16KX16 28SSOP
相关代理商/技术参数
参数描述
ENC424J600T-IPT 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Stand-Alone 10/100 Ethernet Controller with SPI or Parallel Interface
ENC431D05A 制造商:未知厂家 制造商全称:未知厂家 功能描述:
ENC431D-05A 制造商:未知厂家 制造商全称:未知厂家 功能描述:STD MOV
ENC431D07A 制造商:未知厂家 制造商全称:未知厂家 功能描述:
ENC431D-07A 制造商:未知厂家 制造商全称:未知厂家 功能描述:STD MOV
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*