收藏本站
参数资料
型号： ENC424J600T-I/ML
厂商： Microchip Technology
文件页数： 24/168页
文件大小： 0K
描述： IC ETHERNET CTRLR W/SPI 44-QFN
视频文件： Fast 100 Mbps Ethernet PICtail Plus Overview
标准包装： 1,600
控制器类型： 以太网控制器（IEEE 802.3）
接口： SPI
电源电压： 3 V ~ 3.6 V
电流 - 电源： 96mA
工作温度： -40°C ~ 85°C
安装类型： 表面贴装
封装/外壳： 44-VQFN 裸露焊盘
供应商设备封装： 44-QFN（8x8）
包装： 带卷 (TR)
配用： AC164132-ND - BOARD DAUGHTER PICTAIL ETHERNET
ENC424J600/624J600
DS39935C-page 10
2010 Microchip Technology Inc.
2.3
Voltage and Bias Pin
2.3.1
VDD AND VSS PINS
To reduce on-die noise levels and provide for the
high-current demands of Ethernet, there are many
power pins on ENC424J600/624J600 devices:
VDD and VSS
VDDOSC and VSSOSC
VDDPLL and VSSPLL
VDDRX and VSSRX
VDDTX and VSSTX
Each VDD and VSS pin pair above should have a 0.1
F
ceramic bypass capacitor placed as close to the pins as
possible. For best EMI emission suppression, other
smaller capacitors, such as 0.001
F, should be placed
immediately across VDDTX/VSSTX and VDDPLL/VSSPLL.
All VDD power supply pins must be externally con-
nected to the same 3.3V ±10% power source. Similarly,
all VSS supply references must be externally connected
to the same ground node. If a ground connection
appears on two pins (e.g., VSSTX), connect both pins;
do not allow either to float. In addition, it is
recommended that the exposed bottom metal pad on
the 44-pin QFN package be tied to VSS.
Placing ferrite beads or inductors between any two of
the supply pins (e.g., between VDDOSC and VDDRX) is
not recommended. However, it is acceptable to isolate
all of the VDD supplies from the main circuit power sup-
ply through a single ferrite bead or inductor, if desired
for supply noise suppression reasons. Such isolation is
generally not necessary.
2.3.2
VCAP PIN
Most of the device’s digital logic operates at a nominal
1.8V. This voltage is supplied by an on-chip voltage
regulator, which generates the digital supply voltage
from the VDD rail. The only external component
required is an external filter capacitor, connected from
the VCAP pin to ground, as shown in Figure 2-3. A value
of at least 10
F is recommended.
The capacitor must also have a relatively low Equiva-
lent Series Resistance (ESR). It is recommended that
a low-ESR capacitor (ceramic, tantalum or similar)
should be used and high-ESR capacitors (such as
aluminum electrolytic) should be avoided.
The internal regulator is not designed to drive external
loads; therefore, do not attach other circuitry to VCAP.
FIGURE 2-3:
VCAP CONNECTIONS
2.3.3
RBIAS PIN
The internal analog circuitry in the PHY module
requires that an external 12.4 k, 1% resistor be
attached from RBIAS to ground, as shown in
Figure 2-4. The resistor influences the TPOUT+/-
signal amplitude. The RBIAS resistor should be placed
as close as possible to the chip with no immediately
adjacent signal traces in order to prevent noise
capacitively coupling into the pin and affecting the
transmit behavior. It is recommended that the resistor
be a surface mount type.
FIGURE 2-4:
RBIAS RESISTOR
VDD
VCAP
VSS
ENCX24J600
10
F
3.3V
0.1
F
Regulator
+3.3V
I/O, PHY
+1.8V
Core, RAM,
MAC
RBIAS
ENCX24J600
12.4
k1%
PHY
相关PDF资料
PDF描述
PIC16F677-E/P IC PIC MCU FLASH 2KX14 20DIP
MCP2155-I/P IC IRDA PROTOCOL CTRLR 18DIP
MCP2150T-I/SS IC IRDA STD CONTROLLER 20SSOP
MCP2155T-I/SO IC IRDA PROTOCOL CONTRLR 18-SOIC
PIC18F25J10T-I/SS IC PIC MCU FLASH 16KX16 28SSOP
相关代理商/技术参数
参数描述
ENC424J600T-IPT 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Stand-Alone 10/100 Ethernet Controller with SPI or Parallel Interface
ENC431D05A 制造商:未知厂家 制造商全称:未知厂家 功能描述:
ENC431D-05A 制造商:未知厂家 制造商全称:未知厂家 功能描述:STD MOV
ENC431D07A 制造商:未知厂家 制造商全称:未知厂家 功能描述:
ENC431D-07A 制造商:未知厂家 制造商全称:未知厂家 功能描述:STD MOV
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*