参数资料
型号: EPC16QI100
厂商: Altera
文件页数: 15/36页
文件大小: 0K
描述: IC CONFIG DEVICE 16MBIT 100-PQFP
产品培训模块: Three Reasons to Use FPGA's in Industrial Designs
标准包装: 66
系列: EPC
可编程类型: 系统内可编程
存储容量: 16Mb
电源电压: 3 V ~ 3.6 V
工作温度: -40°C ~ 85°C
封装/外壳: 100-BQFP
供应商设备封装: 100-PQFP(14x20)
包装: 托盘
产品目录页面: 604 (CN2011-ZH PDF)
其它名称: 544-1227
Page 22
Pin Description
Enhanced Configuration (EPC) Devices Datasheet
January 2012
Altera Corporation
Pin Description
Table 8 through Table 10 list the EPC device pins. These tables include configuration
interface pins, external flash interface pins, JTAG interface pins, and other pins.
Table 8. Configuration Interface Pins
Pin Name
Pin Type
Description
DATA[7..0]
Output
Configuration data output bus. DATA changes on each falling edge of DCLK . DATA
is latched into the FPGA on the rising edge of DCLK.
DCLK
Output
The DCLK output pin from the EPC device serves as the FPGA configuration clock.
DATA
is latched by the FPGA on the rising edge of DCLK.
nCS
Input
The nCS pin is an input to the EPC device and is connected to the FPGA’s
CONF
_DONE signal for error detection after all configuration data is transmitted to
the FPGA. The FPGA will always drive nCS and OE low when nCONFIG is asserted.
This pin contains a programmable internal weak pull-up resistor of 6 K
that can
be disabled or enabled in the Quartus II software through the Disable nCS and
OE pull-ups on configuration device option.
nINIT_CONF
Open-Drain Output
The nINIT_CONF pin can be connected to the nCONFIG pin on the FPGA to
initiate configuration from the EPC device using a private JTAG instruction. This
pin contains an internal weak pull-up resistor of 6K
that is always active. The
INIT
_CONF pin does not need to be connected if its functionality is not used. If
n
INIT
_CONF is not used, nCONFIG must be pulled to VCC either directly or
through a pull-up resistor.
OE
Open-Drain
Bidirectional
This pin is driven low when POR is not complete. A user-selectable 2-ms or
100-ms counter holds off the release of OE during initial power up to permit
voltage levels to stabilize. POR time can be extended by externally holding OE low.
OE
is connected to the FPGA nSTATUS signal. After the EPC device controller
releases OE, it waits for the nSTATUS-OE line to go high before starting the FPGA
configuration process. This pin contains a programmable internal weak pull-up
resistor of 6 K
that can be disabled or enabled in the Quartus II software
through the Disable nCS and OE pull-ups on configuration device option.
相关PDF资料
PDF描述
LTC4211IS8#TRPBF IC CONTROLLER HOT SWAP 8-SOIC
V48C8H100BL3 CONVERTER MOD DC/DC 8V 100W
AGM22DTAN CONN EDGECARD 44POS R/A .156 SLD
FMC50DRYH-S13 CONN EDGCARD 100POS .100 EXTEND
V48C8H100BL CONVERTER MOD DC/DC 8V 100W
相关代理商/技术参数
参数描述
EPC16QI100N 功能描述:FPGA-配置存储器 IC - Ser. Config Mem Flash 16Mb 33 MHz RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20
EPC16UC88 功能描述:FPGA-配置存储器 IC - Ser. Config Mem Flash 16Mb 33 MHz RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20
EPC16UC88AA 功能描述:IC CONFIG DEVICE 16MBIT 88-UBGA RoHS:否 类别:集成电路 (IC) >> 存储器 - 用于 FPGA 的配置 Proms 系列:EPC 产品变化通告:Product Discontinuation 28/Jul/2010 标准包装:98 系列:- 可编程类型:OTP 存储容量:300kb 电源电压:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC(0.154",3.90mm 宽) 供应商设备封装:8-TSOP 包装:管件
EPC16UC88N 功能描述:FPGA-配置存储器 IC - Ser. Config Mem Flash 16Mb 33 MHz RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20
EPC16UI88AA 功能描述:FPGA-配置存储器 IC - Ser. Config Mem Flash 16Mb 33 MHz RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20