- 您现在的位置：买卖IC网 > PDF目录19908 > EPC16QI100 (Altera)IC CONFIG DEVICE 16MBIT 100-PQFP PDF资料下载
参数资料
| 型号： | EPC16QI100 |
| 厂商： | Altera |
| 文件页数： | 9/36页 |
| 文件大小： | 0K |
| 描述： | IC CONFIG DEVICE 16MBIT 100-PQFP |
| 产品培训模块： | Three Reasons to Use FPGA's in Industrial Designs |
| 标准包装： | 66 |
| 系列： | EPC |
| 可编程类型： | 系统内可编程 |
| 存储容量： | 16Mb |
| 电源电压： | 3 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 100-BQFP |
| 供应商设备封装： | 100-PQFP（14x20） |
| 包装： | 托盘 |
| 产品目录页面： | 604 (CN2011-ZH PDF) |
| 其它名称： | 544-1227 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
Functional Description
Page 17
Enhanced Configuration (EPC) Devices Datasheet
January 2012
Altera Corporation
If an external power up monitoring circuit is connected to the RP# pin with the
loop-back connection, use the following guidelines to avoid contention on the RP#
line:
■
The power-up sequence on the 3.3-V supply should complete within 50 ms of
power up. The 3.3-V VCC should reach the minimum VCC before 50 ms and RP#
should then be released.
■ RP#
should be driven low by the power-up monitoring circuit during power up.
After power up, RP# should be tri-stated externally by the power-up monitoring
circuit.
If the preceding guidelines cannot be completed within 50 ms, then the OEpin must be
driven low externally until RP# is ready to be released.
Dynamic Configuration (Page Mode)
The dynamic configuration (or page mode) feature allows the EPC device to store up
to eight different sets of designs for all the FPGAs in your system. You can then
choose which page (set of configuration files) the EPC device should use for FPGA
configuration.
Dynamic configuration or the page mode feature enables you to store a minimum of
two pages—a factory default or fail-safe configuration and an application
configuration. The fail-safe configuration page could be programmed during system
production, while the application configuration page could support remote or local
updates. These remote updates could add or enhance system features and
performance. However, with remote update capabilities comes the risk of possible
corruption of configuration data. In the event of such a corruption, the system could
automatically switch to the fail-safe configuration and avoid system downtime.
The EPC device page mode feature works with the Stratix remote system
configuration feature, to enable intelligent remote updates to your systems.
f For more information about remotely updating Stratix FPGAs, refer to the Remote
System Configuration with Stratix & Stratix GX Devices chapter in the Stratix Device
Handbook.
The three PGM[2..0]input pins control which page is used for configuration and these
pins are sampled at the start of each configuration cycle when OE goes high. The page
mode selection allows you to dynamically reconfigure the functionality of your FPGA
by switching the PGM[2..0] pins and asserting nCONFIG. Page 0 is defined as the
default page and the PGM[2] pin is the MSB.
1 The PGM[2..0] input pins must not be left floating on your board. When you are not
using this feature, connect the PGM[2..0] pins to GND to select the default page 000.
The EPC device pages are dynamically-sized regions in memory. The start address
and length of each page is programmed into the option-bit space of the flash memory
during initial programming. All subsequent configuration cycles sample the PGM[]
pins and use the option-bit information to jump to the start of the corresponding
configuration page. Each page must have configuration files for all FPGAs in your
system that are connected to that EPC device.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4211IS8#TRPBF | IC CONTROLLER HOT SWAP 8-SOIC |
| V48C8H100BL3 | CONVERTER MOD DC/DC 8V 100W |
| AGM22DTAN | CONN EDGECARD 44POS R/A .156 SLD |
| FMC50DRYH-S13 | CONN EDGCARD 100POS .100 EXTEND |
| V48C8H100BL | CONVERTER MOD DC/DC 8V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EPC16QI100N | 功能描述:FPGA-配置存储器 IC - Ser. Config Mem Flash 16Mb 33 MHz RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20 |
| EPC16UC88 | 功能描述:FPGA-配置存储器 IC - Ser. Config Mem Flash 16Mb 33 MHz RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20 |
| EPC16UC88AA | 功能描述:IC CONFIG DEVICE 16MBIT 88-UBGA RoHS:否 类别:集成电路 (IC) >> 存储器 - 用于 FPGA 的配置 Proms 系列:EPC 产品变化通告:Product Discontinuation 28/Jul/2010 标准包装:98 系列:- 可编程类型:OTP 存储容量:300kb 电源电压:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-TSOP 包装:管件 |
| EPC16UC88N | 功能描述:FPGA-配置存储器 IC - Ser. Config Mem Flash 16Mb 33 MHz RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20 |
| EPC16UI88AA | 功能描述:FPGA-配置存储器 IC - Ser. Config Mem Flash 16Mb 33 MHz RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20 |
发布紧急采购，3分钟左右您将得到回复。