参数资料
型号: EPF10K200SFC484-1X
厂商: Altera
文件页数: 38/100页
文件大小: 0K
描述: IC FLEX 10KS FPGA 200K 484-FBGA
产品培训模块: Three Reasons to Use FPGA's in Industrial Designs
标准包装: 60
系列: FLEX-10KE®
LAB/CLB数: 1248
逻辑元件/单元数: 9984
RAM 位总计: 98304
输入/输出数: 369
门数: 513000
电源电压: 2.375 V ~ 2.625 V
安装类型: 表面贴装
工作温度: 0°C ~ 85°C
封装/外壳: 484-BGA
供应商设备封装: 484-FBGA(23x23)
其它名称: EPF10K200SFC4841X
42
Altera Corporation
FLEX 10KE Embedded Programmable Logic Devices Data Sheet
PCI Pull-Up Clamping Diode Option
FLEX 10KE devices have a pull-up clamping diode on every I/O,
dedicated input, and dedicated clock pin. PCI clamping diodes clamp the
signal to the VCCIO value and are required for 3.3-V PCI compliance.
Clamping diodes can also be used to limit overshoot in other systems.
Clamping diodes are controlled on a pin-by-pin basis. When VCCIO is
3.3 V, a pin that has the clamping diode option turned on can be driven by
a 2.5-V or 3.3-V signal, but not a 5.0-V signal. When VCCIO is 2.5 V, a pin
that has the clamping diode option turned on can be driven by a 2.5-V
signal, but not a 3.3-V or 5.0-V signal. Additionally, a clamping diode can
be activated for a subset of pins, which would allow a device to bridge
between a 3.3-V PCI bus and a 5.0-V device.
Slew-Rate Control
The output buffer in each IOE has an adjustable output slew rate that can
be configured for low-noise or high-speed performance. A slower slew
rate reduces system noise and adds a maximum delay of 4.3 ns. The fast
slew rate should be used for speed-critical outputs in systems that are
adequately protected against noise. Designers can specify the slew rate
pin-by-pin or assign a default slew rate to all pins on a device-wide basis.
The slow slew rate setting affects the falling edge of the output.
Open-Drain Output Option
FLEX 10KE devices provide an optional open-drain output (electrically
equivalent to open-collector output) for each I/O pin. This open-drain
output enables the device to provide system-level control signals (e.g.,
interrupt and write enable signals) that can be asserted by any of several
devices. It can also provide an additional wired-OR plane.
MultiVolt I/O Interface
The FLEX 10KE device architecture supports the MultiVolt I/O interface
feature, which allows FLEX 10KE devices in all packages to interface with
systems of differing supply voltages. These devices have one set of VCC
pins for internal operation and input buffers (VCCINT), and another set for
I/O output drivers (VCCIO).
相关PDF资料
PDF描述
24AA02HT-I/OT IC EEPROM 2KBIT 400KHZ SOT23-5
EP1S20F780I6 IC STRATIX FPGA 20K LE 780-FBGA
EP1S20F780C5 IC STRATIX FPGA 20K LE 780-FBGA
EP1S25F672I7 IC STRATIX FPGA 25K LE 672-FBGA
5-445011-1 CONN D-SUB PLUG HSING 44POS HD
相关代理商/技术参数
参数描述
EPF10K200SFC484-2 功能描述:FPGA - 现场可编程门阵列 FPGA - Flex 10K 1248 LABs 369 IOs RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 栅极数量: 逻辑块数量:943 内嵌式块RAM - EBR:1956 kbit 输入/输出端数量:128 最大工作频率:800 MHz 工作电源电压:1.1 V 最大工作温度:+ 70 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-256
EPF10K200SFC484-2N 功能描述:FPGA - 现场可编程门阵列 FPGA - Flex 10K 1248 LABs 369 IOs RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 栅极数量: 逻辑块数量:943 内嵌式块RAM - EBR:1956 kbit 输入/输出端数量:128 最大工作频率:800 MHz 工作电源电压:1.1 V 最大工作温度:+ 70 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-256
EPF10K200SFC484-2X 功能描述:FPGA - 现场可编程门阵列 FPGA - Flex 10K 1248 LABs 369 IOs RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 栅极数量: 逻辑块数量:943 内嵌式块RAM - EBR:1956 kbit 输入/输出端数量:128 最大工作频率:800 MHz 工作电源电压:1.1 V 最大工作温度:+ 70 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-256
EPF10K200SFC484-3 功能描述:FPGA - 现场可编程门阵列 FPGA - Flex 10K 1248 LABs 369 IOs RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 栅极数量: 逻辑块数量:943 内嵌式块RAM - EBR:1956 kbit 输入/输出端数量:128 最大工作频率:800 MHz 工作电源电压:1.1 V 最大工作温度:+ 70 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-256
EPF10K200SFC484-3N 功能描述:FPGA - 现场可编程门阵列 FPGA - Flex 10K 1248 LABs 369 IOs RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 栅极数量: 逻辑块数量:943 内嵌式块RAM - EBR:1956 kbit 输入/输出端数量:128 最大工作频率:800 MHz 工作电源电压:1.1 V 最大工作温度:+ 70 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-256