- 您现在的位置：买卖IC网 > PDF目录16559 > EV-ADF4156SD1Z (Analog Devices Inc)BOARD EVAL FOR ADF4156 PDF资料下载
参数资料
| 型号： | EV-ADF4156SD1Z |
| 厂商： | Analog Devices Inc |
| 文件页数： | 10/24页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR ADF4156 |
| 标准包装： | 1 |
| 主要目的： | 计时，频率合成器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | ADF4156 |
| 主要属性： | 单路分数-N PLL |
| 次要属性： | 6.2GHz |
| 已供物品： | 板，CD |
ADF4156
Data Sheet
Rev. E | Page 18 of 24
In most cases, this method also provides faster lock times than
the bandwidth switching mode method. In extreme cases, where
cycle slips do not exist in the settling transient, the bandwidth
switching mode can be used.
Cycle Slip Reduction Mode
Cycle slips occur in integer-N/fractional-N synthesizers when
the loop bandwidth is narrow compared with the PFD frequency.
The phase error at the PFD inputs accumulates too fast for the
PLL to correct, and the charge pump temporarily pumps in the
wrong direction. This slows down the lock time dramatically.
The ADF4156 contains a cycle slip reduction circuit to extend
the linear range of the PFD, allowing faster lock times without
requiring loop filter changes.
When the ADF4156 detects that a cycle slip is about to occur, it
turns on an extra charge-pump current cell. This either outputs
a constant current to the loop filter or removes a constant current
from the loop filter, depending on whether the VCO tuning
voltage needs to increase or decrease to acquire the new frequency.
As a result, the linear range of the PFD is increased. Stability is
maintained because the current is constant, not pulsed.
If the phase error increases to a point where another cycle slip
is likely, the ADF4156 turns on another charge-pump cell. This
process continues until the ADF4156 detects that the VCO
frequency is beyond the desired frequency. The extra charge-pump
cells then begin to turn off one by one until they are all turned
off and the frequency is settled.
Up to seven extra charge-pump cells can be turned on. In most
applications, this is sufficient to eliminate cycle slips altogether,
resulting in much faster lock times.
Setting Bit DB28 in the MOD/R register (R2) to 1 enables cycle
slip reduction. A 45% to 55% duty cycle is needed on the signal
at the PFD for CSR to operate correctly. Note that CSR cannot
be used if the phase detector polarity is set to negative; therefore,
a noninverting loop filter topology should be used with CSR.
Dynamic Bandwidth Switching Mode
The dynamic bandwidth switching mode involves increasing
the loop filter bandwidth for a set time at the beginning of the
locking transient. This is achieved by boosting the charge-pump
current from the set value in Register R2 to the maximum setting.
To maintain loop stability during this period, it is necessary to
modify the loop filter by adding a switch and resistor. When the
new frequency is programmed to the ADF4156 in this mode, three
events occur simultaneously to put the device in wideband mode:
A timeout counter is started.
The charge-pump current is boosted from its set current to
the maximum setting.
The fast-lock switch (available via MUXOUT) is activated.
The timeout counter in Register R4 defines the period that the
device is kept in wideband mode. During wideband mode, the
PLL acquires lock faster due to the wider loop filter bandwidth.
Stability is maintained at the optimal 45° setting due to the use
of the extra resistor in the loop filter.
When the timeout counter times out, the charge-pump current
is reduced from the maximum setting to its set current, and the
fast-lock switch is deactivated. The device is then in narrow-
band mode, and spurs are attenuated.
To ensure optimum lock time, the timeout counter should be
set to time out when the PLL is close to the final frequency. If
the switch is deactivated, a spike in the settling transient will be
observed due to charge insertion from the switch. Because the
PLL is in narrow-band mode, this spike can take some time to
settle out. This is one of the disadvantages of the bandwidth
switching mode compared with the cycle slip reduction mode.
Fast Lock: An Example
If a PLL has a reference frequency of 13 MHz, a fPFD of 13 MHz,
and a required lock time of 50 s, the PLL is set to wide bandwidth
for 40 s.
If the time set for the wide bandwidth is 40 s, then
Fast-Lock Timer Value = Time in Wide Bandwidth × fPFD
Fast-Lock Timer Value = 40 s × 13 MHz = 520
Therefore, 520 must be loaded into Bits DB[18:7] of Register R4.
The clock divider mode bits (DB[20:19]) in Register R4 must also
be set to 01 to activate this mode. To activate the fast-lock switch
on the MUXOUT pin, the MUXOUT control bits (DB[30:27])
in Register R0 must be set to 1100.
Fast Lock: Loop Filter Topology
To use fast-lock mode, an extra connection from the PLL to the
loop filter is needed. The damping resistor in the loop filter
must be reduced to of its value while in wide bandwidth
mode. This is required because the charge-pump current is
increased by 16 while in wide bandwidth mode and stability
must be ensured. When the ADF4156 is in fast-lock mode (that
is, when the fast-lock switch is programmed to appear at the
MUXOUT pin), the MUXOUT pin is automatically shorted to
ground. The following two topologies can be used:
Topology 1: Divide the damping resistor (R1) into two
values (R1 and R1A) that have a ratio of 1:3 (see Figure 22).
Topology 2: Connect an extra resistor (R1A) directly from
MUXOUT, as shown in Figure 23. The extra resistor must
be chosen such that the parallel combination of an extra
resistor and the damping resistor (R1) is reduced to of
the original value of R1 (see Figure 23).
相关PDF资料 |
PDF描述 |
|---|---|
| GEM22DTBT | CONN EDGECARD 44POS R/A .156 SLD |
| GEM22DTAT | CONN EDGECARD 44POS R/A .156 SLD |
| V48C24E150BL3 | CONVERTER MOD DC/DC 24V 150W |
| GSM12DSES | CONN EDGECARD 24POS .156 EYELET |
| MCP100T-485I/TT | IC SUPERVISOR ACTIVE LOW SOT23-3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EV-ADF4157SD1Z | 功能描述:BOARD EVAL FOR ADF4157 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
| EV-ADF4159EB1Z | 制造商:Analog Devices 功能描述:EVALUATION BOARD - Boxed Product (Development Kits) 制造商:Analog Devices 功能描述:EVAL BOARD FOR ADF4159 |
| EV-ADF4159EB2Z | 制造商:Analog Devices 功能描述:13GHZFRAC-NPLL+ADF55XXVCO+3VADM - Boxed Product (Development Kits) |
| EV-ADF4159EB3Z | 制造商:Analog Devices 功能描述:EVALUATIONBOARD - Boxed Product (Development Kits) 制造商:Analog Devices 功能描述:EVAL BOARD FOR ADF4159 制造商:Analog Devices 功能描述:Clock & Timer Development Tools ADF4159 EVAL BRD |
| EV-ADF4360-0EB1Z | 功能描述:BOARD EVAL FOR ADF4360-0 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
发布紧急采购，3分钟左右您将得到回复。