- 您现在的位置：买卖IC网 > PDF目录16601 > EVAL-AD5292EBZ (Analog Devices Inc)BOARD EVAL FOR AD5292 PDF资料下载
参数资料
| 型号： | EVAL-AD5292EBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 16/32页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD5292 |
| 标准包装： | 1 |
| 主要目的： | 数字电位器 |
| 嵌入式： | 是 |
| 已用 IC / 零件： | AD5292 |
| 主要属性： | 1 通道，1024 位置 |
| 次要属性： | SPI 接口 |
| 已供物品： | 板，CD |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
AD5291/AD5292
Rev. D | Page 23 of 32
20-TP MEMORY
Once a desirable wiper position is found, the contents of the
RDAC register can be saved into a 20-TP memory register
(see Table 12). Thereafter, the wiper position is always set at that
position for any future on-off-on power supply sequence. The
AD5291 and AD5292 have an array of 20 one-time programmable
(OTP) memory registers. When the desired word is programmed
to 20-TP memory, the device automatically verifies that the
program command was successful. The verification process
includes margin testing. Bit C3 of the control register can be
polled to verify that the fuse program command was successful.
Programming data to 20-TP memory consumes approximately
25 mA for 550 μs and takes approximately 8 ms to complete.
During this time, the shift register is locked, preventing any
changes from taking place. The RDY pin can be used to monitor
the completion of the 20-TP memory program and verification.
No change in supply voltage is required to program the 20-TP
memory. However, a 1 μF capacitor on the EXT_CAP pin is
required (see Figure 68). Prior to 20-TP activation, the AD5291
and AD5292 preset to midscale on power-up.
WRITE PROTECTION
On power-up, the shift register write commands for both the
RDAC register and the 20-TP memory register are disabled.
The RDAC write protect bit, C1 of the control register (see
Table 13 and Table 14), is set to 0 by default. This disables any
change of the RDAC register content regardless of the software
commands, except that the RDAC register can be refreshed
from the 20-TP memory using the software reset command
(Command 4) or through hardware by the RESET pin. To enable
programming of the variable resistor wiper position (program-
ming the RDAC register), the write protect bit, C1 of the control
register, must first be programmed. This is accomplished by
loading the shift register with Command 6 (see
). To
enable programming of the 20-TP memory block bit, C0 of the
control register (set to 0 by default) must first be set to 1.
Table 12. Write and Read to RDAC and 20-TP Memory
DIN
SDO
Action
0x1803
0xXXXX
Enable update of wiper position and 20-TP memory contents through digital interface.
0x0500
0x1803
Write 0x100 to the RDAC register; wiper moves to full-scale position.
0x0800
0x0500
Prepare data read from the RDAC register.
0x0C00
0x0100
Stores RDAC register content into 20-TP memory. The 16-bit word appears out of SDO, where the last 10 bits
contain the contents of the RDAC register (0x100).
0x1C00
0x0C00
Prepare data read from the control register.
0x0000
0x000X
NOP Instruction 0 sends 16-bit word out of SDO, where the last four bits contain the contents of the control
register. If Bit C3 = 1, the fuse program command is successful.
Table 13. Control Register Bit Map1
DB9
DB8
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
X
C3
C2
C1
C0
1 X = don’t care.
Table 14. Control Register Function
Bit Name
Description
C0
20-TP program enable
0 = 20-TP program disabled (default)
1 = enable device for 20-TP program
C1
RDAC register write protect
0 = wiper position frozen to value in memory (default)1
1 = allow update of wiper position through digital Interface
C2
Calibration enable
0 = resistor performance mode enabled (default)
1 = normal mode enabled
C3
20-TP memory program success
0 = fuse program command unsuccessful (default)
1 = fuse program command successful
1 Wiper position frozen to value last programmed in 20-TP memory. Wiper is frozen to midscale if 20-TP memory has not been previously programmed.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B3N-EW | CONVERTER MOD DC/DC 18.5V 100W |
| VI-B3K-EX | CONVERTER MOD DC/DC 40V 75W |
| VE-B6P-EX | CONVERTER MOD DC/DC 13.8V 75W |
| VE-B6P-EW | CONVERTER MOD DC/DC 13.8V 100W |
| H3AKH-2018G | IDC CABLE - HSC20H/AE20G/HPK20H |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-AD5360EBZ | 功能描述:BOARD EVAL FOR AD5360 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5360EBZ1 | 制造商:AD 制造商全称:Analog Devices 功能描述:16-Channel, 16-/14-Bit, Serial Input, Voltage-Output DAC |
| EVAL-AD5361EBZ | 功能描述:BOARD EVAL FOR AD5361 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5361EBZ1 | 制造商:AD 制造商全称:Analog Devices 功能描述:16-Channel, 16-/14-Bit, Serial Input, Voltage-Output DAC |
| EVAL-AD5362EBZ | 功能描述:BOARD EVAL FOR AD5362 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
发布紧急采购，3分钟左右您将得到回复。