- 您现在的位置：买卖IC网 > PDF目录16601 > EVAL-AD5292EBZ (Analog Devices Inc)BOARD EVAL FOR AD5292 PDF资料下载
参数资料
| 型号： | EVAL-AD5292EBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 17/32页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD5292 |
| 标准包装： | 1 |
| 主要目的： | 数字电位器 |
| 嵌入式： | 是 |
| 已用 IC / 零件： | AD5292 |
| 主要属性： | 1 通道，1024 位置 |
| 次要属性： | SPI 接口 |
| 已供物品： | 板，CD |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
AD5291/AD5292
Rev. D | Page 24 of 32
BASIC OPERATION
The basic mode of setting the variable resistor wiper position
(programming the RDAC register) is accomplished by loading
the shift register with Command 1 (see Table 11) and the desired
wiper position data. When the desired wiper position is deter-
mined, the user can load the shift register with Command 3
(see Table 11), which stores the wiper position data in the 20-TP
memory register. After 6 ms, the wiper position is permanently
stored in the 20-TP memory. The RDY pin can be used to moni-
tor the completion of this 20-TP program. Table 12 provides a
programming example, listing the sequence of serial data input
(DIN) words with the serial data output appearing at the SDO
pin in hexadecimal format.
20-TP READBACK AND SPARE MEMORY STATUS
It is possible to read back the contents of any of the 20-TP
memory registers through SDO by using Command 5 (see
Table 11). The lower five LSB bits (D0 to D4) of the data byte
select which memory location is to be read back (see Table 16).
Data from the selected memory location are clocked out of the
SDO pin during the next SPI operation, where the last 10 bits
contain the contents of the specified memory location.
It is also possible to calculate the address of the most recently
programmed memory location by reading back the contents of
read-only Memory Address 0x14 and Memory Address 0x15
using Command 5. The data bytes read back from Memory
Address 0x014 and Memory Address 0x015 are thermometer
encoded versions of the address of the last programmed
memory location.
For the example outlined in Table 15, the address of the last
programmed location is calculated as
(Number of Bits = 1 in Memory Address 0x14) + (Number
of Bits = 1 in Memory Address 0x15) 1 = 10 + 8 1 = 17
(0x10)
If no memory location has been programmed, then the address
generated is 1.
SHUTDOWN MODE
The AD5291 and AD5292 can be placed in shutdown mode by
executing the software shutdown command, Command 8 (see
Table 11), and setting the LSB, D0, to 1. This feature places the
RDAC in a special state in which Terminal A is open-circuited,
and Wiper W is connected to Terminal B. The contents of the
RDAC register are unchanged by entering shutdown mode.
However, all commands listed in Table 11 are supported while
in shutdown mode. Execute Command 8 (see Table 11), and set
the LSB, D0, to 0 to exit shutdown mode.
Table 15. Example 20-TP Memory Readback
DIN
SDO
Action
0x1414
0xXXXX
Prepares data read from Memory Address 0x14.
0x1415
0x03FF
Prepares data read from Memory Address 0x15. Sends 16-bit word out of SDO, where the last 10 bits contain the
contents of Memory Address 0x14.
0x0000
0x00FF
NOP Command 0 sends 16-bit word out of SDO, where last 10-bits contain the contents of Memory Address 0x15.
0x1410
0x0000
Prepares data read from memory location 0x10.
0x0000
0xXXXX
NOP Instruction 0 sends 16-bit word out of SDO, where the last 10 bits contain the contents of Memory Address 0x10 (17).
Table 16. Memory Map of Command 5
Data Bits [DB9:DB0]1
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
Register Contents
X
0
1st programmed wiper location (0x00)
X
0
1
2nd programmed wiper location (0x01)
X
0
1
0
3rd programmed wiper location (0x02)
X
0
1
4th programmed wiper location (0x03)
X
0
1
0
5th programmed wiper location (0x04)
…
X
0
1
0
1
10th programmed wiper location (0x09)
X
0
1
0
15th programmed wiper location (0x0E)
X
1
0
1
20th programmed wiper location (0x13)
X
1
0
1
0
Programmed memory status (thermometer encoded)2 (0x14)
X
1
0
1
0
1
Programmed memory status (thermometer encoded)2 (0x15)
1 X = don’t care.
2 Allows the user to calculate the remaining spare memory locations.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B3N-EW | CONVERTER MOD DC/DC 18.5V 100W |
| VI-B3K-EX | CONVERTER MOD DC/DC 40V 75W |
| VE-B6P-EX | CONVERTER MOD DC/DC 13.8V 75W |
| VE-B6P-EW | CONVERTER MOD DC/DC 13.8V 100W |
| H3AKH-2018G | IDC CABLE - HSC20H/AE20G/HPK20H |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-AD5360EBZ | 功能描述:BOARD EVAL FOR AD5360 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5360EBZ1 | 制造商:AD 制造商全称:Analog Devices 功能描述:16-Channel, 16-/14-Bit, Serial Input, Voltage-Output DAC |
| EVAL-AD5361EBZ | 功能描述:BOARD EVAL FOR AD5361 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5361EBZ1 | 制造商:AD 制造商全称:Analog Devices 功能描述:16-Channel, 16-/14-Bit, Serial Input, Voltage-Output DAC |
| EVAL-AD5362EBZ | 功能描述:BOARD EVAL FOR AD5362 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
发布紧急采购，3分钟左右您将得到回复。