- 您现在的位置：买卖IC网 > PDF目录17036 > EVAL-AD7682EDZ (Analog Devices Inc)BOARD EVAL AD7682 PDF资料下载
参数资料
| 型号： | EVAL-AD7682EDZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 20/32页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL AD7682 |
| 标准包装： | 1 |
| 系列： | PulSAR® |
| ADC 的数量： | 1 |
| 位数： | 16 |
| 采样率（每秒）： | 250k |
| 数据接口： | 串行 |
| 输入范围： | ±VREF |
| 在以下条件下的电源（标准）： | 12.5mW @ 250kSPS，5V |
| 工作温度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD7682 |
| 已供物品： | 板 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
Data Sheet
AD7682/AD7689
Rev. D | Page 27 of 32
GENERAL TIMING WITH A BUSY INDICATOR
Figure 38 details the timing for all three modes: read/write
during conversion (RDC), read/write after conversion (RAC),
and read/write spanning conversion (RSC). Note that the gating
item for both CFG and data readback is at the end of conversion
(EOC). As detailed previously, the data access should occur up
to safe data reading/writing time, tDATA. If the full CFG word is
not written to prior to EOC, it is discarded and the current
configuration remains.
At the EOC, if CNV is low, the busy indicator is enabled. In
addition, to generate the busy indicator properly, the host must
assert a minimum of 17 SCK falling edges to return SDO to high
impedance because the last bit on SDO remains active. Unlike the
case detailed in the Read/Write Spanning Conversion Without a
Busy Indicator section, if the conversion result is not read out
fully prior to EOC, the last bit clocked out remains. If this bit is
low, the busy signal indicator cannot be generated because the
busy generation requires either a high impedance or a remaining
bit high-to-low transition. A good example of this occurs when
an SPI host sends 16 SCKs because these are usually limited to
8-bit or 16-bit bursts; thus the LSB remains. Because the transi-
greater), the LSB is low 50% of the time. For this interface, the SPI
host needs to burst 24 SCKs, or a QSPI interface can be used and
programmed for 17 SCKs.
The SCK can idle high or low depending on the CPOL and
CPHA settings if SPI is used. A simple solution is to use CPOL =
CPHA = 1 (not shown) with SCK idling high.
From power-up, in any read/write mode, the first three conver-
sion results are undefined because a valid CFG does not take
place until the 2nd EOC; thus, two dummy conversions are
required. Also, if the state machine writes the CFG during the
power-up state (RDC shown), the CFG register needs to be
rewritten again at the next phase. Note that the first valid data
occurs in Phase (n + 1) when the CFG register is written during
Phase (n 1).
ACQUISITION
(n – 1) UNDEFINED
ACQUISITION
(n)
ACQUISITION
(n + 1)
ACQUISITION
(n + 2)
PHASE
POWER
UP
EOC
START OF CONVERSION
(SOC)
EOC
CONVERSION
(n)
CONVERSION
(n + 1)
CONVERSION
(n – 2) UNDEFINED
07
35
3-
04
4
tCONV
tCYC
tDATA
CNV
DIN
RDC
RAC
RSC
SDO
NOTES
1. CNV MUST BE LOW PRIOR TO THE END OF CONVERSION (EOC) TO GENERATE THE BUSY INDICATOR.
2. A TOTAL OF 17 SCK FALLING EDGES ARE REQUIRED TO RETURN SDO TO HIGH-Z. IF CFG READBACK IS ENABLED,
A TOTAL OF 31 SCK FALLING EDGES IS REQUIRED TO RETURN SDO TO HIGH-Z.
DATA (n)
DATA (n – 1)
XXX
DATA (n – 2)
XXX
DATA (n – 2)
XXX
DATA (n – 2)
XXX
DATA (n – 2)
XXX
DATA (n – 1)
XXX
DATA (n – 1)
XXX
DATA (n – 1)
XXX
DATA (n – 3)
XXX
DIN
SDO
DATA (n + 1)
DATA (n)
DATA (n + 1)
DIN
CFG (n)
CFG (n + 2)
CFG (n + 1)
CFG (n + 3)
SDO
SCK
1
SCK
1n
n + 1
17
1
n
n + 1
17
1
n
n + 1
17
SCK
1
XXX
NOTE 1
NOTE 2
CFG (n)
CFG (n + 1)
CFG (n + 2)
CFG (n)
CFG (n + 1)
CFG (n + 2)
CFG (n + 3)
CONVERSION
(n – 1) UNDEFINED
相关PDF资料 |
PDF描述 |
|---|---|
| LGU2E331MELZ | CAP ALUM 330UF 250V 20% SNAP |
| EVAL-AD7982SDZ | BOARD EVAL FOR AD7982 |
| VI-J1L-EY | CONVERTER MOD DC/DC 28V 50W |
| VE-21L-EY | CONVERTER MOD DC/DC 28V 50W |
| DC1009A-A | BOARD DELTA SIGMA ADC LTC2492 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-AD7683CB | 制造商:AD 制造商全称:Analog Devices 功能描述:16-Bit, 100 kSPS PulSAR ADC in MSOP/QFN |
| EVAL-AD7683CBZ | 制造商:Analog Devices 功能描述:EVAL BOARD 18BIT 100ksps I.C. |
| EVAL-AD7683SDZ | 功能描述:数据转换 IC 开发工具 EVAL BOARD 18BIT 100ksps I.C. RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| EVAL-AD7684CBZ | 功能描述:BOARD EVALUATION FOR AD7684 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:PulSAR® 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD7685CB | 制造商:Analog Devices 功能描述:Evaluation Board For Use With Either The Analog Devices 制造商:Analog Devices 功能描述:EVAL FOR AD7685 - Bulk 制造商:Rochester Electronics LLC 功能描述:EVAL FOR AD7685 - Bulk |
发布紧急采购，3分钟左右您将得到回复。