- 您现在的位置：买卖IC网 > PDF目录17036 > EVAL-AD7682EDZ (Analog Devices Inc)BOARD EVAL AD7682 PDF资料下载
参数资料
| 型号： | EVAL-AD7682EDZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 21/32页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL AD7682 |
| 标准包装： | 1 |
| 系列： | PulSAR® |
| ADC 的数量： | 1 |
| 位数： | 16 |
| 采样率（每秒）： | 250k |
| 数据接口： | 串行 |
| 输入范围： | ±VREF |
| 在以下条件下的电源（标准）： | 12.5mW @ 250kSPS，5V |
| 工作温度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD7682 |
| 已供物品： | 板 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
AD7682/AD7689
Data Sheet
Rev. D | Page 28 of 32
CHANNEL SEQUENCER
scanning channels in a repeated fashion. Channels are scanned
as singles or pairs, with or without the temperature sensor, after
the last channel is sequenced.
The sequencer starts with IN0 and finishes with IN[7:0] set in
CFG[9:7]. For paired channels, the channels are paired depend-
ing on the last channel set in CFG[9:7]. Note that in sequencer
mode, the channels are always paired with the positive input on
the even channels (IN0, IN2, IN4, IN6), and with the negative
input on the odd channels (IN1, IN3, IN5, IN7). For example,
setting CFG[9:7] = 110 or 111 scans all pairs with the positive
inputs dedicated to IN0, IN2, IN4, and IN6.
CFG[2:1] are used to enable the sequencer. After the CFG
register is updated, DIN must be held low while reading data
out for Bit 13, or the CFG register begins updating again.
Note that while operating in a sequence, some bits of the CFG
register can be changed. However, if changing CFG[11] (paired
or single channel) or CFG[9:7] (last channel in sequence), the
sequence reinitializes and converts IN0 (or IN0/IN1 pairs) after
the CFG register is updated.
Figure 39 details the timing for all three modes without a busy
indicator. Refer to the Read/Write Spanning Conversion
Without a Busy Indicator section and the Read/Write Spanning
Conversion Without a Busy Indicator section for more details.
The sequencer can also be used with the busy indicator and
details for these timings can be found in the General Timing
with a Busy Indicator section and the Read/Write Spanning
Conversion with a Busy Indicator section.
For sequencer operation, the CFG register should be set during
the (n 1) phase after power-up. On phase (n), the sequencer
setting takes place and acquires IN0. The first valid conversion
result is available at phase (n + 1). After the last channel set in
CFG[9:7] is converted, the internal temperature sensor data is
output (if enabled), followed by acquisition of IN0.
Examples
With all channels configured for unipolar mode to GND,
including the internal temperature sensor, the sequence scans in
the following order:
IN0, IN1, IN2, IN3, IN4, IN5, IN6, IN7, TEMP, IN0, IN1, IN2, …
For paired channels with the internal temperature sensor
enabled, the sequencer scans in the following order:
IN0, IN2, IN4, IN6, TEMP, IN0, …
Note that IN1, IN3, IN5, and IN7 are referenced to a GND
ACQUISITION
(n – 1) UNDEFINED
ACQUISITION
(n), IN0
ACQUISITION
(n + 1), IN1
ACQUISITION
(n + 2), IN2
PHASE
POWER
UP
EOC
SOC
EOC
CONVERSION
(n – 1) UNDEFINED
CONVERSION
(n), IN0
CONVERSION
(n + 1), IN1
CONVERSION
(n – 2) UNDEFINED
07
35
3-
0
4
6
tCONV
tCYC
tDATA
CNV
DIN
SDO
XXX
MSB
XXX
MSB
XXX
NOTES
1. CNV MUST BE HIGH PRIOR TO THE END OF CONVERSION (EOC) TO AVOID THE BUSY INDICATOR.
2. A TOTAL OF 16 SCK FALLING EDGES ARE REQUIRED TO RETURN SDO TO HIGH-Z. IF CFG READBACK IS ENABLED,
A TOTAL OF 30 SCK FALLING EDGES IS REQUIRED TO RETURN SDO TO HIGH-Z.
DATA IN0
DATA (n – 1)
XXX
DATA (n – 1)
XXX
DATA (n – 1)
XXX
DATA (n – 1)
XXX
DATA (n – 2)
XXX
DATA (n – 2)
XXX
DATA (n – 2)
XXX
DATA (n – 2)
XXX
DATA (n – 3)
XXX
MSB
IN0
MSB
IN1
DIN
SDO
DATA IN1
DATA IN0
DATA IN1
DIN
CFG (n)
SDO
SCK
1
NOTE 1
16
NOTE 2
2
1
SCK
116
16
nn
n
n + 1
n
1
SCK
1
116
16
1
CFG (n)
RDC
RAC
RSC
CFG (n)
Figure 39. General Channel Sequencer Timing Without a Busy Indicator
相关PDF资料 |
PDF描述 |
|---|---|
| LGU2E331MELZ | CAP ALUM 330UF 250V 20% SNAP |
| EVAL-AD7982SDZ | BOARD EVAL FOR AD7982 |
| VI-J1L-EY | CONVERTER MOD DC/DC 28V 50W |
| VE-21L-EY | CONVERTER MOD DC/DC 28V 50W |
| DC1009A-A | BOARD DELTA SIGMA ADC LTC2492 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-AD7683CB | 制造商:AD 制造商全称:Analog Devices 功能描述:16-Bit, 100 kSPS PulSAR ADC in MSOP/QFN |
| EVAL-AD7683CBZ | 制造商:Analog Devices 功能描述:EVAL BOARD 18BIT 100ksps I.C. |
| EVAL-AD7683SDZ | 功能描述:数据转换 IC 开发工具 EVAL BOARD 18BIT 100ksps I.C. RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| EVAL-AD7684CBZ | 功能描述:BOARD EVALUATION FOR AD7684 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:PulSAR® 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD7685CB | 制造商:Analog Devices 功能描述:Evaluation Board For Use With Either The Analog Devices 制造商:Analog Devices 功能描述:EVAL FOR AD7685 - Bulk 制造商:Rochester Electronics LLC 功能描述:EVAL FOR AD7685 - Bulk |
发布紧急采购，3分钟左右您将得到回复。