- 您现在的位置：买卖IC网 > PDF目录17044 > EVAL-AD7690SDZ (Analog Devices Inc)BOARD EVAL FOR AD7690 PDF资料下载
参数资料
| 型号： | EVAL-AD7690SDZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 13/24页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD7690 |
| 标准包装： | 1 |
| 系列： | PulSAR® |
| ADC 的数量： | 1 |
| 位数： | 18 |
| 采样率（每秒）： | 400k |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 输入范围： | ±VREF |
| 在以下条件下的电源（标准）： | 17mW @ 100kSPS |
| 工作温度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD7690 |
| 已供物品： | 板 |
AD7690
Rev. B | Page 20 of 24
CS MODE, 4-WIRE WITH BUSY INDICATOR
This mode is usually used when a single AD7690 is connected
to an SPI-compatible digital host, which has an interrupt input,
and it is desired to keep CNV, which is used to sample the analog
input, independent of the signal used to select the data reading.
This independence is particularly important in applications where
low jitter on CNV is desired.
The connection diagram is shown in Figure 40, and the
corresponding timing is given in Figure 41.
With SDI high, a rising edge on CNV initiates a conversion,
selects the CS mode, and forces SDO to high impedance. In this
mode, CNV must be held high during the conversion phase and
the subsequent data readback. (If SDI and CNV are low, SDO is
driven low.) Prior to the minimum conversion time, SDI can be
used to select other SPI devices, such as analog multiplexers,
but SDI must be returned low before the minimum conversion
time elapses and then held low for the maximum possible
conversion time to guarantee the generation of the busy signal
indicator. When the conversion is complete, SDO goes from
high impedance to low impedance. With a pull-up on the SDO
line, this transition can be used as an interrupt signal to initiate
the data readback controlled by the digital host. The AD7690
then enters the acquisition phase and powers down. The data
bits are clocked out, MSB first, by subsequent SCK falling edges.
The data is valid on both SCK edges. Although the rising edge
can be used to capture the data, a digital host using the SCK
falling edge allows a faster reading rate, provided it has an
acceptable hold time. After the optional 19th SCK falling edge or
SDI going high (whichever occurs first), SDO returns to high
impedance.
DATA IN
IRQ
CLK
CONVERT
CS1
VIO
DIGITAL HOST
47k
CNV
SCK
SDO
SDI
AD7690
05
79
2-
01
7
Figure 40. 4-Wire CS Mode with Busy Indicator Connection Diagram
SDO
D17
D16
D1
D0
tDIS
SCK
1
2
3
171819
tSCK
tSCKL
tSCKH
tHSDO
tDSDO
tEN
CONVERSION
ACQUISITION
tCONV
tCYC
tACQ
ACQUISITION
SDI
CNV
tSSDICNV
tHSDICNV
05
79
2-
01
8
Figure 41. 4-Wire CS Mode with Busy Indicator Serial Interface Timing
相关PDF资料 |
PDF描述 |
|---|---|
| 0210490944 | CABLE JUMPER 1.25MM .051M 25POS |
| EVAL-AD7980SDZ | BOARD EVAL FOR AD7980 |
| PH50S2412 | CONVERTER DC/DC 12V 50W 6-PIN |
| 1624094-9 | INDUCTOR 220UH 100MA 1812 |
| EVAL-AD7685SDZ | BOARD EVAL FOR AD7685 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-AD7691CBZ | 功能描述:BOARD EVALUATION FOR AD7691CBZ RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:PulSAR® 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD7691SDZ | 功能描述:BOARD EVAL FOR AD7691 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:PulSAR® 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD7693CB | 制造商:Analog Devices 功能描述:EVAL KIT FOR 16BIT, 0.5 LSB, 500 KSPS PULSARDIFFERENTIAL ADC - Bulk |
| EVAL-AD7693CBZ | 功能描述:BOARD EVALUATION FOR AD7693 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:PulSAR® 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD7693SDZ | 功能描述:数据转换 IC 开发工具 EVAL BOARD 16-bit ADC 500kSPS RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
发布紧急采购，3分钟左右您将得到回复。