- 您现在的位置：买卖IC网 > PDF目录17044 > EVAL-AD7690SDZ (Analog Devices Inc)BOARD EVAL FOR AD7690 PDF资料下载
参数资料
| 型号： | EVAL-AD7690SDZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 23/24页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD7690 |
| 标准包装： | 1 |
| 系列： | PulSAR® |
| ADC 的数量： | 1 |
| 位数： | 18 |
| 采样率（每秒）： | 400k |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 输入范围： | ±VREF |
| 在以下条件下的电源（标准）： | 17mW @ 100kSPS |
| 工作温度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD7690 |
| 已供物品： | 板 |
AD7690
Rev. B | Page 8 of 24
TERMINOLOGY
Integral Nonlinearity Error (INL)
INL refers to the deviation of each individual code from a line
drawn from negative full scale through positive full scale. The
point used as negative full scale occurs LSB before the first
code transition. Positive full scale is defined as a level 1 LSB
beyond the last code transition. The deviation is measured from
the middle of each code to the true straight line (see Figure 25).
Differential Nonlinearity Error (DNL)
In an ideal ADC, code transitions are 1 LSB apart. DNL is the
maximum deviation from this ideal value. It is often specified in
terms of resolution for which no missing codes are guaranteed.
Zero Error
Zero error is the difference between the ideal midscale voltage,
that is, 0 V, from the actual voltage producing the midscale
output code, that is, 0 LSB.
Gain Error
The first transition (from 100 ... 00 to 100 ... 01) should occur at
a level LSB above nominal negative full scale (4.999981 V
for the ±5 V range). The last transition (from 011 … 10 to
011 … 11) should occur for an analog voltage 1 LSB below the
nominal full scale (+4.999943 V for the ±5 V range). The gain
error is the deviation of the difference between the actual level
of the last transition and the actual level of the first transition
from the difference between the ideal levels.
Spurious-Free Dynamic Range (SFDR)
SFDR is the difference, in decibels, between the rms amplitude
of the input signal and the peak spurious signal.
Effective Number of Bits (ENOB)
ENOB is a measurement of the resolution with a sine wave
input. It is related to SINAD by the following formula:
ENOB = (SINADdB 1.76)/6.02
and is expressed in bits.
Noise-Free Code Resolution
Noise-free code resolution is the number of bits beyond which it is
impossible to distinctly resolve individual codes. It is calculated as:
Noise-Free Code Resolution = log2(2N/Peak-to-Peak Noise)
and is expressed in bits.
Effective Resolution
Effective resolution is calculated as
Effective Resolution = log2(2N/RMS Input Noise)
and is expressed in bits.
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of the first five harmonic
components to the rms value of a full-scale input signal and is
expressed in decibels.
Dynamic Range
Dynamic range is the ratio of the rms value of the full scale to
the total rms noise measured with the inputs shorted together.
The value for dynamic range is expressed in decibels.
Signal-to-Noise Ratio (SNR)
SNR is the ratio of the rms value of the actual input signal to the
rms sum of all other spectral components that is less than the
Nyquist frequency, excluding harmonics and dc. The value of
SNR is expressed in decibels.
Signal-to-(Noise + Distortion) Ratio (SINAD)
SINAD is the ratio of the rms value of the actual input signal to
the rms sum of all other spectral components below the Nyquist
frequency, including harmonics but excluding dc. The value for
SINAD is expressed in decibels.
Aperture Delay
Aperture delay is the measure of the acquisition performance. It
is the time between the rising edge of the CNV input and when
the input signal is held for a conversion.
Transient Response
Transient response is the time required for the ADC to accurately
acquire its input after a full-scale step function is applied.
相关PDF资料 |
PDF描述 |
|---|---|
| 0210490944 | CABLE JUMPER 1.25MM .051M 25POS |
| EVAL-AD7980SDZ | BOARD EVAL FOR AD7980 |
| PH50S2412 | CONVERTER DC/DC 12V 50W 6-PIN |
| 1624094-9 | INDUCTOR 220UH 100MA 1812 |
| EVAL-AD7685SDZ | BOARD EVAL FOR AD7685 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-AD7691CBZ | 功能描述:BOARD EVALUATION FOR AD7691CBZ RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:PulSAR® 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD7691SDZ | 功能描述:BOARD EVAL FOR AD7691 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:PulSAR® 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD7693CB | 制造商:Analog Devices 功能描述:EVAL KIT FOR 16BIT, 0.5 LSB, 500 KSPS PULSARDIFFERENTIAL ADC - Bulk |
| EVAL-AD7693CBZ | 功能描述:BOARD EVALUATION FOR AD7693 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:PulSAR® 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD7693SDZ | 功能描述:数据转换 IC 开发工具 EVAL BOARD 16-bit ADC 500kSPS RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
发布紧急采购，3分钟左右您将得到回复。