- 您现在的位置：买卖IC网 > PDF目录17031 > EVAL-AD7715-3EBZ (Analog Devices Inc)BOARD EVALUATION FOR AD7715 PDF资料下载
参数资料
| 型号： | EVAL-AD7715-3EBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 28/40页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR AD7715 |
| 标准包装： | 1 |
| ADC 的数量： | 1 |
| 位数： | 16 |
| 采样率（每秒）： | 500 |
| 数据接口： | 串行 |
| 输入范围： | ±VREF/增益 |
| 在以下条件下的电源（标准）： | 5.3mW @ 3.3 V |
| 工作温度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD7715-3 |
| 已供物品： | 板，CD |
| 相关产品： | AD7715ARUZ-5-ND - IC ADC 16BIT SIGMA-DELTA 16TSSOP AD7715ARUZ-3-ND - IC ADC 16BIT SIGMA-DELTA 16TSSOP AD7715ANZ-3-ND - IC ADC 16BIT SIGMA-DELTA 16DIP AD7715ARUZ-5REEL7-ND - IC ADC 16BIT SIGMA-DELTA 16TSSOP AD7715ARUZ-3REEL7-ND - IC ADC 16BIT SIGMA-DELTA 16TSSOP AD7715ARZ-3REEL-ND - IC ADC 16BIT SIGMA-DELTA 16SOIC AD7715ARZ-3-ND - IC ADC 16BIT 3V 16-SOIC AD7715ANZ-5-ND - IC ADC 16BIT 5V 16-DIP AD7715ARZ-5REEL-ND - IC ADC 16BIT 5V 16-SOIC AD7715ARZ-5-ND - IC ADC 16BIT SIGMA-DELTA 16-SOIC 更多... |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
AD7715
Rev. D | Page 34 of 40
CODE FOR SETTING UP THE AD7715
The C Code for Interfacing AD7715 to 68HC11 section gives
a set of read and write routines in C code for interfacing the
68HC11 microcontroller to the AD7715. The sample program
sets up the various registers on the AD7715 and reads 1000
samples from the part into the 68HC11. The setup conditions
on the part are exactly the same as those outlined for the
flowchart of Figure 10. In the example code given here, the
DRDY output is polled to determine if a new valid word is
available in the data register.
The sequence of the events in this program are as follows:
1.
Write to the communications register, setting the gain to 1
with standby inactive.
2.
Write to the setup register, setting bipolar mode, buffer
off, no filter synchronization, confirming a clock frequency
of 2.4576 MHz, setting the output rate for 60 Hz and
initiating a self-calibration.
3.
Poll the DRDY output.
4.
Read the data from the data register.
5.
Loop around doing Step 3 and Step 4 until the specified
number of samples have been taken.
C CODE FOR INTERFACING AD7715 TO 68HC11
/* This program has read and write routines for the 68HC11 to interface to the AD7715 and the sample
program sets the various registers and then reads 1000 samples from the part. */
#include <math.h>
#include <io6811.h>
#define NUM_SAMPLES 1000 /* change the number of data samples */
#define MAX_REG_LENGTH 2 /* this says that the max length of a register is 2 bytes */
Writetoreg (int);
Read (int,char);
char *datapointer = store;
char store[NUM_SAMPLES*MAX_REG_LENGTH + 30];
void main()
{
/* the only pin that is programmed here from the 68HC11 is the /CS and this is why the PC2 bit
of PORTC is made as an output */
char a;
DDRC = 0x04; /* PC2 is an output the rest of the port bits are inputs */
PORTC | = 0x04; /* make the /CS line high */
Writetoreg(0x10); /* set the gain to 1, standby off and set the next operation as write to the setup
register */
Writetoreg(0x68); /* set bipolar mode, buffer off, no filter sync, confirm clock as 2.4576MHz, set
output rate to 60Hz and do a self calibration */
while(PORTC & 0x10); /* wait for /DRDY to go low */
for(a=0;a<NUM_SAMPLES;a++);
{
Writetoreg(0x38); /*set the next operation for 16 bit read from the data register */
Read(NUM_SAMPLES,2);
}
Writetoreg(int byteword);
{
int q;
SPCR = 0x3f;
SPCR = 0X7f; /* this sets the WiredOR mode(DWOM=1), Master mode(MSTR=1), SCK idles high(CPOL=1), /SS
can be low always (CPHA=1), lowest clock speed(slowest speed which is master clock /32 */
DDRD = 0x18; /* SCK, MOSI outputs */
q = SPSR;
q = SPDR; /* the read of the staus register and of the data register is needed to clear the interrupt
which tells the user that the data transfer is complete */
相关PDF资料 |
PDF描述 |
|---|---|
| MLG1005S0N3C | INDUCTOR MULTILAYER 0.3NH 0402 |
| DC1500A-C | BOARD SAR ADC LTC2391-16 |
| STD17W-F | WIRE & CABLE MARKERS |
| EVAL-AD7705EBZ | BOARD EVALUATION FOR AD7705 |
| DC1500A-B | BOARD SAR ADC LTC2392-16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-AD7715-3EBZ1 | 制造商:AD 制造商全称:Analog Devices 功能描述:3 V/5 V, 450 ??A 16-Bit, Sigma-Delta ADC |
| EVAL-AD7715-5EB | 制造商:Analog Devices 功能描述:EVLAUATION BOARD - Bulk |
| EVAL-AD7716EB | 制造商:Analog Devices 功能描述:LC2MOS 22-BIT DATA ACQUISITION SYSTEM 制造商:Analog Devices 功能描述:EVALUATION BOARD - Bulk |
| EVAL-AD7716EBZ | 制造商:Analog Devices 功能描述:EVAL BRD AD7716 - Bulk |
| EVAL-AD7718EB | 制造商:Analog Devices 功能描述:Evaluation Kit For 8-/10-Channel, Low Voltage, Low Power, Segma-Delta ADCs 制造商:Rochester Electronics LLC 功能描述:EVALUATION BOARD I.C. - Bulk |
发布紧急采购，3分钟左右您将得到回复。