- 您现在的位置：买卖IC网 > PDF目录16522 > EVAL-ADM1064TQEB (Analog Devices Inc)BOARD EVALUATION FOR ADM1064TQ PDF资料下载
参数资料
| 型号： | EVAL-ADM1064TQEB |
| 厂商： | Analog Devices Inc |
| 文件页数： | 16/32页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR ADM1064TQ |
| 标准包装： | 1 |
| 主要目的： | 电源管理，电源监控器/跟踪器/序列发生器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | ADM1064 |
| 主要属性： | 10 通道监控器 / 序列发生器，6 个电压输出 DAC |
| 次要属性： | 通过 SMBus（通过 USB）实现的可编程 GUI |
| 已供物品： | 2 个板，线缆，CD |
| 相关产品： | ADM1064ASUZ-ND - IC SEQUENCER/SUPERVISOR 48-TQFP ADM1064ACPZ-ND - IC SEQUENCER/SUPERVISOR 40-LFCSP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
ADM1064
OUTPUTS
SUPPLY SEQUENCING THROUGH
CONFIGURABLE OUTPUT DRIVERS
Supply sequencing is achieved with the ADM1064 using the
programmable driver outputs (PDOs) on the device as control
signals for supplies. The output drivers can be used as logic
enables or as FET drivers.
The sequence in which the PDOs are asserted (and, therefore, the
supplies are turned on) is controlled by the sequencing engine (SE).
The SE determines what action is taken with the PDOs, based
on the condition of theADM1064 inputs. Therefore, the PDOs
can be set up to assert when the SFDs are in tolerance, the correct
input signals are received on the VXx digital pins, no warnings
are received from any of the inputs of the device, and at other
times. The PDOs can be used for a variety of functions. The
primary function is to provide enable signals for LDOs or dc-
to-dc converters that generate supplies locally on a board. The
PDOs can also be used to provide a PWRGD signal when all the
SFDs are in tolerance or a RESET output if one of the SFDs goes
out of specification (this can be used as a status signal for a DSP,
FPGA, or other microcontroller).
The PDOs can be programmed to pull up to a number of different
options. The outputs can be programmed as follows:
Open drain (allowing the user to connect an external pull-up
resistor).
Open drain with weak pull-up to V DD .
Open drain with strong pull-up to V DD .
Open drain with weak pull-up to VPx.
Open drain with strong pull-up to VPx.
Strong pull-down to GND.
Internally charge-pumped high drive (12 V, PDO1 to PDO6
only).
The last option (available only on PDO1 to PDO6) allows the
user to directly drive a voltage high enough to fully enhance an
external N-FET, which is used to isolate, for example, a card-
side voltage from a backplane supply (a PDO can sustain greater
than 10.5 V into a 1 μA load). The pull-down switches can also
be used to drive status LEDs directly. The data driving each of
the PDOs can come from one of three sources. The source can
be enabled in the PDOxCFG configuration register (see the
AN-698 Application Note at www.analog.com for details).
The data sources are as follows:
Output from the SE.
Directly from the SMBus. A PDO can be configured so that the
SMBus has direct control over it. This enables software control
of the PDOs. Therefore, a microcontroller can be used to
initiate a software power-up/power-down sequence.
On-chip clock. A 100 kHz clock is generated on the device. This
clock can be made available on any of the PDOs. It can be
used, for example, to clock an external device such as an LED.
DEFAULT OUTPUT CONFIGURATION
All of the internal registers in an unprogrammed ADM1064 device
from the factory are set to 0. Because of this, the PDOx pins are
pulled to GND by a weak (20 kΩ) on-chip pull-down resistor.
As the input supply to the ADM1064 ramps up on VPx or VH,
all PDOx pins behave as follows:
Input supply = 0 V to 1.2 V. The PDOs are high impedance.
Input supply = 1.2 V to 2.7 V. The PDOs are pulled to GND by a
weak (20 kΩ) on-chip pull-down resistor.
Supply > 2.7 V. Factory-programmed devices continue to pull
all PDOs to GND by a weak (20 kΩ) on-chip pull-down
resistor. Programmed devices download current EEPROM
configuration data, and the programmed setup is latched. The
PDO then goes to the state demanded by the configuration.
This provides a known condition for the PDOs during
power-up.
The internal pull-down can be overdriven with an external pull-
up of suitable value tied from the PDOx pin to the required pull-up
voltage. The 20 kΩ resistor must be accounted for in calculating
a suitable value. For example, if PDOx must be pulled up to 3.3 V,
and 5 V is available as an external supply, the pull-up resistor
value is given by
3.3 V = 5 V × 20 kΩ/( R UP + 20 kΩ)
Therefore,
R UP = (100 kΩ ? 66 kΩ)/3.3 V = 10 kΩ
VFET (PDO1 TO PDO6 ONLY)
VP4
V DD
SE DATA
SMBus DATA
CFG4 CFG5 CFG6
SEL
VP1
PDO
CLK DATA
Figure 22. Programmable Driver Output
Rev. D | Page 16 of 32
相关PDF资料 |
PDF描述 |
|---|---|
| M3AKK-1018R | IDC CABLE - MSC10K/MC10M/MPK10K |
| 5492193-1 | PIGTAIL SM LDS SCAPC |
| VI-J01-EZ-S | CONVERTER MOD DC/DC 12V 25W |
| 5492022-9 | CA SM LDD FC(NG)TOFC(NG)19FT |
| GMM08DTBT-S189 | CONN EDGECARD 16POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-ADM1064TQEBZ | 制造商:Analog Devices 功能描述:EVAL BOARD - Bulk |
| EVAL-ADM1065LFEB | 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk |
| EVAL-ADM1065LFEBZ | 制造商:Analog Devices 功能描述:EVAL BD FOR ADM1065 SUPER SEQUENCERS - Bulk |
| EVAL-ADM1065TQEB | 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk |
| EVAL-ADM1065TQEBZ | 功能描述:BOARD EVALUATION FOR ADM1065TQ RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
发布紧急采购，3分钟左右您将得到回复。