- 您现在的位置：买卖IC网 > PDF目录16522 > EVAL-ADM1064TQEB (Analog Devices Inc)BOARD EVALUATION FOR ADM1064TQ PDF资料下载
参数资料
| 型号： | EVAL-ADM1064TQEB |
| 厂商： | Analog Devices Inc |
| 文件页数： | 19/32页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR ADM1064TQ |
| 标准包装： | 1 |
| 主要目的： | 电源管理，电源监控器/跟踪器/序列发生器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | ADM1064 |
| 主要属性： | 10 通道监控器 / 序列发生器，6 个电压输出 DAC |
| 次要属性： | 通过 SMBus（通过 USB）实现的可编程 GUI |
| 已供物品： | 2 个板，线缆，CD |
| 相关产品： | ADM1064ASUZ-ND - IC SEQUENCER/SUPERVISOR 48-TQFP ADM1064ACPZ-ND - IC SEQUENCER/SUPERVISOR 40-LFCSP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
ADM1064
Monitoring Fault Detector
The monitoring fault detector block is used to detect a failure
on an input. The logical function implementing this is a wide
OR gate that can detect when an input deviates from its expected
condition. The clearest demonstration of the use of this block
is in the PWRGD state, where the monitor block indicates that
a failure on one or more of the VP1,VP2, or VP3 inputs has
occurred.
No programmable delay is available in this block because the
triggering of a fault condition is likely to be caused by a supply
falling out of tolerance. In this situation, the device needs to
react as quickly as possible. Some latency occurs when moving
out of this state because it takes a finite amount of time (~20 μs)
for the state configuration to download from EEPROM into the SE.
MONITORING FAULT
DETECTOR
1-BIT FAULT
DETECTOR
Timeout Detector
The timeout detector allows the user to trap a failure to ensure
proper progress through a power-up or power-down sequence.
In the sample application shown in Figure 25, the timeout next-
state transition is from the EN3V3 and EN2V5 states. For the
EN3V3 state, the signal 3V3ON is asserted on the PDO1 output
pin upon entry to this state to turn on a 3.3 V supply. This supply
rail is connected to the VP2 pin, and the sequence detector looks
for the VP2 pin to go above its undervoltage threshold, which is
set in the supply fault detector (SFD) attached to that pin.
The power-up sequence progresses when this change is
detected. If, however, the supply fails (perhaps due to a short
circuit overloading this supply), the timeout block traps the
problem. In this example, if the 3.3 V supply fails within 10 ms,
the SE moves to the DIS3V3 state and turns off this supply by
bringing PDO1 low. It also indicates that a fault has occurred by
taking PDO3 high. Timeout delays of 100 μs to 400 ms can be
programmed.
VP1
SUPPLY FAULT
DETECTION
MASK
SENSE
FAULT
FAULT AND STATUS REPORTING
The ADM1064 has a fault latch for recording faults. Two registers,
FSTAT1 and FSTAT2, are set aside for this purpose. A single bit
is assigned to each input of the device, and a fault on that input
VX5
LOGIC INPUT CHANGE
OR FAULT DETECTION
1-BIT FAULT
DETECTOR
FAULT
MASK
SENSE
sets the relevant bit. The contents of the fault register can be
read out over the SMBus to determine which input(s) faulted.
The fault register can be enabled/disabled in each state. To latch
data from one state, ensure that the fault latch is disabled in the
following state. This ensures that only real faults are captured
and not, for example, undervoltage conditions that may be
1-BIT FAULT
DETECTOR
present during a power-up or power-down sequence.
WARNINGS
MASK
FAULT
The ADM1064 also has a number of status registers. These include
more detailed information, such as whether an undervoltage or
overvoltage fault is present on a particular input. The status
registers also include information on ADC limit faults. Note that
Figure 26. Monitoring Fault Detector Block Diagram
the data in the status registers is not latched in any way and,
therefore, is subject to change at any time.
See the AN-698 Application Note at www.analog.com for full
details about the ADM1064 registers.
Rev. D | Page 19 of 32
相关PDF资料 |
PDF描述 |
|---|---|
| M3AKK-1018R | IDC CABLE - MSC10K/MC10M/MPK10K |
| 5492193-1 | PIGTAIL SM LDS SCAPC |
| VI-J01-EZ-S | CONVERTER MOD DC/DC 12V 25W |
| 5492022-9 | CA SM LDD FC(NG)TOFC(NG)19FT |
| GMM08DTBT-S189 | CONN EDGECARD 16POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-ADM1064TQEBZ | 制造商:Analog Devices 功能描述:EVAL BOARD - Bulk |
| EVAL-ADM1065LFEB | 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk |
| EVAL-ADM1065LFEBZ | 制造商:Analog Devices 功能描述:EVAL BD FOR ADM1065 SUPER SEQUENCERS - Bulk |
| EVAL-ADM1065TQEB | 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk |
| EVAL-ADM1065TQEBZ | 功能描述:BOARD EVALUATION FOR ADM1065TQ RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
发布紧急采购，3分钟左右您将得到回复。