- 您现在的位置：买卖IC网 > PDF目录68993 > FA5515P (FUJI ELECTRIC CO LTD) 1.5 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDIP8 PDF资料下载
参数资料
| 型号： | FA5515P |
| 厂商： | FUJI ELECTRIC CO LTD |
| 元件分类： | 稳压器 |
| 英文描述： | 1.5 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDIP8 |
| 封装： | DIP-8 |
| 文件页数： | 7/22页 |
| 文件大小： | 260K |
| 代理商： | FA5515P |
FA551X
15
1.2 Connecting the startup resistor after rectification
(DC line)
When the startup resistor is connected after rectification (DC
line) as shown in Figure 19, the voltage applied to the startup
resistor becomes the peak value of the AC input voltage.
Startup resistor R1 must satisfy the three equations shown
below. Select a smaller-side value for R1 in consideration of
temperature characteristics.
(a) To supply startup current 30A at ON threshold voltage
17.5V (max.) of UVLO:
(b) To supply IC consumption current 80A (max.) (Vcc =10V)
in latch mode:
(c) To supply IC consumption current 200A (max.) (Vcc = 17V)
in the off state under the on/off function:
If neither the latch nor the on/off functions are used, only the
expression in (8) needs to be satisfied. In this method, after
latch mode operation, smoothing capacitor C1 in the main
circuit supplies current to the IC via the startup resistor even if
the AC input is shut down. Therefore, some time must elapse
before the latch mode is reset.
2. Determining the Vcc capacitor value
To properly start the power supply, a certain value is required
for the capacitor connected to the VCC pin. Figure 20 shows
the Vcc voltage at start-up when a proper value is given to the
capacitor. When the input power is turned on, the capacitor
connected to the VCC pin is charged via the startup resistor
and the voltage increases. The IC is then in standby state and
almost no current is consumed. (Icc<2A) Thereafter, Vcc
reaches the ON threshold voltage of UVLO and the IC begins
operation. When the IC begins operation to make output, the IC
operates based on the voltage from the auxiliary winding.
When the IC is just starting up, however, it takes time for the
voltage from the auxiliary winding to rise enough, and Vcc
drops during this period.
Determine the Vcc capacitor value so that Vcc will not drop
down to the OFF threshold voltage of UVLO during this period.
If the Vcc capacitor value is too small, Vcc will drop to the OFF
threshold voltage of UVLO before the auxiliary winding voltage
rises enough. If so, Vcc repeatedly goes up and down between
the UVLO threshold voltages, and the power supply cannot
start up. (Figure 21)
Fig. 19
Startup circuit (2)
C2
C1
MOSFET
D1
T1
FA551X
~
+
–
DB
AC INPUT
R1
Rs
OUT
VCC
6
5
Fig. 20
Vcc voltage at startup with a adequate capacitor
Fig. 21
Vcc voltage at startup with a inadequate capacitor
UVLO
ON
UVLO
OFF
Vcc
Time t
Auxiliary winding
voltage
Vcc must not drop to
UVLO OFF.
UVLO
ON
UVLO
OFF
Vcc
Time t
........................................................ (9)
R1
2
Vac – 10
0.08
...................................................... (8)
R1
2
Vac – 17.5
0.03
R1: Startup resistance [k
]
Vac: Effective value of AC input voltage [V]
...................................................... (10)
R1
2
Vac – 17
0.2
相关PDF资料 |
PDF描述 |
|---|---|
| FA5514N | 1.5 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO8 |
| FA5515N | 1.5 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO8 |
| FA5510N | 1.5 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO8 |
| FA5511P | 1.5 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDIP8 |
| FA5514P | 1.5 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDIP8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FA5515P-D1 | 制造商:Fuji Electric 功能描述: |
| FA551X | 制造商:未知厂家 制造商全称:未知厂家 功能描述:CMOS IC For Switching Power Supply Control |
| FA5526 | 制造商:FUJI 制造商全称:Fuji Electric 功能描述:Fuji Switching Power Control IC |
| FA5527 | 制造商:FUJI 制造商全称:Fuji Electric 功能描述:Fuji Switching Power Control IC |
| FA5527P-A2 | 制造商:Fuji Electric 功能描述: |
发布紧急采购，3分钟左右您将得到回复。