参数资料
型号: FAN5069EMTCX
厂商: Fairchild Semiconductor
文件页数: 12/22页
文件大小: 622K
描述: IC REG DL BCK/LINEAR 16TSSOP
产品变化通告: Metallization Mask Rev 18/Apr/2007
标准包装: 2,500
拓扑: 降压(降压)同步(1),线性(LDO)(1)
功能: 任何功能
输出数: 2
频率 - 开关: 200kHz
电压/电流 - 输出 1: 控制器
电压/电流 - 输出 2: 控制器
带 LED 驱动器:
带监控器:
带序列发生器:
电源电压: 4.5 V ~ 5.5 V
工作温度: -40°C ~ 85°C
安装类型: *
封装/外壳: 16-TSSOP(0.173",4.40mm 宽)
供应商设备封装: *
包装: 带卷 (TR)
?2005 Fairchild Semiconductor Corporation
www.fairchildsemi.com
FAN5069 Rev. 1.1.5
12
ture is disabled during the start-up until the voltage on
the SS capacitor crosses 1.2V.
To achieve current limit, the FAN5069 monitors the
inductor current during the OFF time by monitoring and
holding the voltage across the lower MOSFET. The volt-
age across the lower MOSFET is sensed between the
PGND and the SW pins.
The output of the summing amplifier is a function of the
inductor current, R
DS_ON
 of the bottom FET and the gain
of the current sense amplifier. With the R
DS_ON
 method
of current sensing, the current limit can vary widely from
unit to unit. R
DS_ON
 not only varies from unit to unit, but
also has a typical junction temperature coefficient of
about 0.4%/癈 (consult the MOSFET datasheet for
actual values). The set point of the actual current limit
decreases in proportion to increase in MOSFET die tem-
perature. A factor of 1.6 in the current limit set point typi-
cally compensates for all MOSFET R
DS_ON
  variations,
assuming the MOSFET's heat sinking keeps its operat-
ing die temperature below 125癈.
For more accurate current limit setting, use resistor
sensing. In a resistor sensing scheme, an appropriate
current sense resistor is connected between the source
terminal of the bottom MOSFET and PGND.
Set the current limit by choosing R
ILIM
 as follows:
 (EQ. 5)
where R
ILIM
 is in K?
I
MAX
 is the maximum load current.
K1 is a constant to accommodate for the variation of
MOSFET R
DS(ON)
 (typically 1.6).
With K1 = 1.6, I
MAX
= 20A, R
DS(ON)
= 7m? V
IN
 = 24V,
V
OUT
 = 1.5V, F
SW
 = 300 KHz, R
RAMP
= 400 K? R
ILIM
 
calculates to be 323.17K?
Auto Restart (PWM)
The FAN5069 supports two modes of response when the
internal fault latch is set. The user can configure it to
keep the power supply latched in the OFF state OR in
the Auto Restart mode. When the EN pin is tied to V
CC
,
the power supply is latched OFF. When the EN pin is ter-
minated with a 100nF to GND, the power supply is in
Auto Restart mode. The table below describes the rela-
tionship between PWM restart and setting on EN pin. Do
not leave the EN pin open without any capacitor.
The fault latch can also be reset by recycling the V
CC
 to
the controller.
Under Voltage Protection (PWM)
The PWM converter output is monitored constantly for
under voltage at the FB pin. If the voltage on the FB pin
stays lower than 75% of internal Vref for 16 clock cycles,
the fault latch is set and the converter shuts down. This
shutdown feature is disabled during startup until the volt-
age on the SS capacitor reaches 1.2V.
Over Voltage Protection (PWM)
The PWM converter output voltage is monitored con-
stantly at the FB pin for over voltage. If the voltage on the
FB pin stays higher than 115% of internal V
REF
 for two
clock cycles, the controller turns OFF the upper MOS-
FET and turns ON the lower MOSFET. This crowbar
action stops when the voltage on the FB pin reaches
0.4V to prevent the output voltage from becoming nega-
tive. This over-voltage protection (OVP) feature is active
as soon as the voltage on the EN pin becomes high.
Turning ON the low-side MOSFETs on an OVP condition
pulls down the output, resulting in a reverse current,
which starts to build up in the inductor. If the output over-
voltage is due to failure of the high-side MOSFET, this
crowbar action pulls down the input supply or blows its
fuse, protecting the system, which is very critical.
During soft-start, if the output overshoots beyond 115%
of V
REF
, the output voltage is brought down by the low-
side MOSFET until the voltage on the FB pin goes below
0.4V. The fault latch is NOT set until the voltage on the
SS pin reaches 1.2V. Once the fault latch is set, the con-
verter shuts down.
Figure 21. Over-Voltage Protection
Thermal Fault Protection
The FAN5069 features thermal protection where the IC
temperature is monitored. When the IC junction temper-
ature exceeds +160癈, the controller shuts down and
when the junction temperature gets down to +125癈, the
converter restarts.
R
ILIM
128
K1   I
MAX
R
DSON
10
3
"
"
"
1.43
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
1
1.8
Vin
- - - - - - - - -

?/DIV>
?/DIV>
?/DIV>
?/DIV>
Vout   33.32   10
11
"
"
F
SW
R
RAMP
"
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -- -
"
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
+
+
=
EN Pin
PWM/Restart
Pull to GND
OFF
V
CC
No restart after fault
Cap to GND
Restart after TDELAY (Sec.) =
0.85 x C where C is in 糉
S
R
Q
S
R
Q
FB
0.4V
115% Vref
ILIM
UV
V
SS
>1.2V
Delay
2 Clks
Fault
Latch
LS Drive
OV
EN
相关PDF资料
PDF描述
HIP1011BCB-T IC CTRLR HOT PLUG PCI 16-SOIC
HIP1020CK-T IC CTRLR HOT PLUG SOT23-5
HIP6018BCBZ-T IC REG TRPL BCK/LINEAR 24-SOIC
HIP6021CB-T IC REG QD BCK/LINEAR 28-SOIC
HIP6521CB-T IC REG QD BCK/LINEAR SYNC 16SOIC
相关代理商/技术参数
参数描述
FAN5069MTCX 功能描述:开关变换器、稳压器与控制器 PWM and ULDO Controller Combo RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel
FAN5070 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:High Performance Programmable Synchronous DC-DC Controller
FAN5070M 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:Voltage-Mode SMPS Controller
FAN5071 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:High Performance Programmable Synchronous DC-DC Controller for Multi-Voltage Platforms
FAN5071AB WAF 制造商:Fairchild Semiconductor Corporation 功能描述: