- 您现在的位置：买卖IC网 > PDF目录1922 > FT232HL-REEL (FTDI, Future Technology Devices International Ltd)IC HS USB TO UART/FIFO 48LQFP PDF资料下载
参数资料
| 型号： | FT232HL-REEL |
| 厂商： | FTDI, Future Technology Devices International Ltd |
| 文件页数： | 16/65页 |
| 文件大小： | 0K |
| 描述： | IC HS USB TO UART/FIFO 48LQFP |
| 应用说明： | FT1248 Application Note |
| 标准包装： | 1 |
| 通道数： | 1，UART |
| FIFO's： | 4kb |
| 规程： | RS232，RS422，RS485 |
| 电源电压： | 1.62 V ~ 1.98 V，2.97 V ~ 3.63 V |
| 带并行端口： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-LQFP |
| 供应商设备封装： | 48-LQFP（7x7） |
| 包装： | 标准包装 |
| 其它名称： | 768-1101-6 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页
Copyright 2012 Future Technology Devices International Limited
23
Document No.: FT_000288
FT232H SINGLE CHANNEL HI-SPEED USB TO MULTIPURPOSE UART/FIFO IC
Datasheet Version 1.8
Clearance No.: FTDI #199
4.2 Functional Block Descriptions
Multi-Purpose UART/FIFO Controllers. The FT232H has one independent UART/FIFO Controller. This
controls the UART data, 245 FIFO data, Fast Serial (opto isolation) or Bit-Bang mode which can be
selected by SETUP (FT_SetBitMode) command. Each Multi-Purpose UART/FIFO Controller also contains
an MPSSE (Multi Protocol Synchronous Serial Engine). Using this MPSSE, the Multi-Purpose UART/FIFO
Controller can be configured under software command, to have one of the MPSSE (SPI (MASTER), I2C,
JTAG).
USB Protocol Engine and FIFO control. The USB Protocol Engine controls and manages the interface
between the UTMI PHY and the FIFOs of the chip. It also handles power management and the USB
protocol specification.
Port FIFO TX Buffer (1Kbytes). Data from the Host PC is stored in these buffers to be used by the
Multi-purpose UART/FIFO controllers. This is controlled by the USB Protocol Engine and FIFO control
block.
Port FIFO RX Buffer (1Kbytes). Data from the Multi-purpose UART/FIFO controllers is stored in these
blocks to be sent back to the Host PC when requested. This is controlled by the USB Protocol Engine and
FIFO control block.
RESET Generator – The integrated Reset Generator Cell provides a reliable power-on reset to the device
internal circuitry at power up. The RESET# input pin allows an external device to reset the FT232H.
RESET# should be tied to VCCIO (+3.3V) if not being used.
Baud Rate Generators – The Baud Rate Generators provides a x16 or a x10 clock input to the UART’s
from a 120MHz reference clock and consists of a 14 bit pre-scaler and 4 register bits which provide fine
tuning of the baud rate (used to divide by a number plus a fraction). This determines the Baud Rate of
the UART which is programmable from 183 baud to 12 Mbaud. See FTDI application note AN_120 on the
FTDI website for more details.
EEPROM Interface. If the external EEPROM is fitted, the FT232H can be configured as an asynchronous
serial UART (default mode), parallel FIFO (245) mode, FT1248, fast serial (opto isolation) or CPU-Style
FIFO. The EEPROM should be a 16 bit wide configuration such as a 93LC56B or equivalent capable of a
1Mbit/s clock rate at VCCIO = +2.97V to 3.63V. The EEPROM is programmable in-circuit over USB using
compatible with the FT232H device.
+1.8/3.3V LDO Regulator. The +3.3/+1.8V LDO regulator generates +1.8 volts for the core and the
USB transceiver cell and +3.3V for the IO and the internal PLL and USB PHY power supply.
UTMI PHY. The Universal Transceiver Macrocell Interface (UTMI) physical interface cell. This block
handles the Full speed / Hi-Speed SERDES (serialise – deserialise) function for the USB TX/RX data. It
also provides the clocks for the rest of the chip. A 12 MHz crystal must be connected to the OSCI and
OSCO pins or 12 MHz Oscillator must be connected to the OSCI, and the OSCO is left unconnected. A 12K
Ohm resistor should be connected between REF and GND on the PCB.
The UTMI PHY functions include:
Supports 480 Mbit/s “Hi-Speed” (HS)/ 12 Mbit/s “Full Speed” (FS).
SYNC/EOP generation and checking
Data and clock recovery from serial stream on the USB.
Bit-stuffing/unstuffing; bit stuff error detection.
Manages USB Resume, Wake Up and Suspend functions.
Single parallel data clock output with on-chip PLL to generate higher speed serial data clocks.
相关PDF资料 |
PDF描述 |
|---|---|
| FT232RL-REEL | IC USB FS SERIAL UART 28-SSOP |
| FT245BL-REEL | IC USB FS PARALLEL FIFO 32-LQFP |
| FT245RL-REEL | IC USB TO PARALLEL FIFO 28-SSOP |
| FT4232HQ-REEL | IC USB HS QUAD UART/SYNC 64-QFN |
| FUSB1500MHX | IC USB 2.0 TRANSCEIVER 16-MLP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FT232HL-TRAY | 功能描述:USB 接口集成电路 USB HS to UART/FIFO SPI/JTAG/I2C LQFP-48 RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
| FT232HQ-REEL | 功能描述:USB 接口集成电路 USB HS to UART/FIFO SPI/JTAG/I2C QFN-48 RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
| FT232HQ-TRAY | 功能描述:USB 接口集成电路 USB HS to UART/FIFO SPI/JTAG/I2C QFN-48 RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
| FT232R | 制造商:FTDI 制造商全称:FTDI 功能描述:USB UART IC - Single chip USB to asynchronous serial data transfer interface |
| FT232R_10 | 制造商:FTDI 制造商全称:FTDI 功能描述:USB UART IC - Single chip USB to asynchronous serial data transfer interface |
发布紧急采购，3分钟左右您将得到回复。