参数资料
型号: FT232HL-REEL
厂商: FTDI, Future Technology Devices International Ltd
文件页数: 8/65页
文件大小: 0K
描述: IC HS USB TO UART/FIFO 48LQFP
应用说明: FT1248 Application Note
标准包装: 1
通道数: 1,UART
FIFO's: 4kb
规程: RS232,RS422,RS485
电源电压: 1.62 V ~ 1.98 V,2.97 V ~ 3.63 V
带并行端口:
带故障启动位检测功能:
带调制解调器控制功能:
安装类型: 表面贴装
封装/外壳: 48-LQFP
供应商设备封装: 48-LQFP(7x7)
包装: 标准包装
其它名称: 768-1101-6
Copyright 2012 Future Technology Devices International Limited
16
Document No.: FT_000288
FT232H SINGLE CHANNEL HI-SPEED USB TO MULTIPURPOSE UART/FIFO IC
Datasheet Version 1.8
Clearance No.: FTDI #199
3.5.3 FT232H pins used in an FT245 Style Asynchronous FIFO Interface
The FT232H can be configured as a FT245 style asynchronous FIFO interface. When configured in this
mode, the pins used and the descriptions of the signals are shown in Table 3.8. To enter this mode the
external EEPROM must be set to 245 asynchronous FIFO mode. In this mode, data is written or read on
the falling edge of the RD# or WR# signals.
Pin No.
Name
Type
FT245 Configuration Description
13, 14, 15, 16, 17,
18, 19,20
ADBUS[7:0]
I/O
D7 to D0 bidirectional FIFO data. This bus is normally input
unless RD# is low.
21
RXF#
OUTPUT
When high, do not read data from the FIFO. When low, there is
data available in the FIFO which can be read by driving RD#
low. When RD# goes high again RXF# will always go high and
only become low again if there is another byte to read. During
reset this signal pin is tri-state, but pulled up to VCCIO via an
internal 200kΩ resistor.
25
TXE#
OUTPUT
When high, do not write data into the FIFO. When low, data
can be written into the FIFO by strobing WR# high, then low.
During reset this signal pin is tri-state, but pulled up to VCCIO
via an internal 200kΩ resistor.
26
RD#
INPUT
Enables the current FIFO data byte to be driven onto D0...D7
when RD# goes low. Fetches the next FIFO data byte (if
available) from the receive FIFO buffer when RD# goes high.
27
WR#
INPUT
Writes the data byte on the D0...D7 pins into the transmit FIFO
buffer when WR# goes from high to low.
28
SIWU#
INPUT
The Send Immediate / WakeUp signal combines two functions
on a single pin. If USB is in suspend mode (PWREN# = 1) and
remote wakeup is enabled in the EEPROM, strobing this pin low
will cause the device to request a resume on the USB Bus.
Normally, this can be used to wake up the Host PC.
During normal operation (PWREN# = 0), if this pin is strobed
low any data in the device RX buffer will be sent out over USB
on the next Bulk-IN request from the drivers regardless of the
pending packet size. This can be used to optimize USB transfer
speed for some applications. Tie this pin to VCCIO if not used.
Table 3.8 FT245 Style Asynchronous FIFO Configured Pin Descriptions
For a functional description of this mode, please refer to section 4.5
相关PDF资料
PDF描述
FT232RL-REEL IC USB FS SERIAL UART 28-SSOP
FT245BL-REEL IC USB FS PARALLEL FIFO 32-LQFP
FT245RL-REEL IC USB TO PARALLEL FIFO 28-SSOP
FT4232HQ-REEL IC USB HS QUAD UART/SYNC 64-QFN
FUSB1500MHX IC USB 2.0 TRANSCEIVER 16-MLP
相关代理商/技术参数
参数描述
FT232HL-TRAY 功能描述:USB 接口集成电路 USB HS to UART/FIFO SPI/JTAG/I2C LQFP-48 RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20
FT232HQ-REEL 功能描述:USB 接口集成电路 USB HS to UART/FIFO SPI/JTAG/I2C QFN-48 RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20
FT232HQ-TRAY 功能描述:USB 接口集成电路 USB HS to UART/FIFO SPI/JTAG/I2C QFN-48 RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20
FT232R 制造商:FTDI 制造商全称:FTDI 功能描述:USB UART IC - Single chip USB to asynchronous serial data transfer interface
FT232R_10 制造商:FTDI 制造商全称:FTDI 功能描述:USB UART IC - Single chip USB to asynchronous serial data transfer interface