- 您现在的位置：买卖IC网 > PDF目录1922 > FUSB2805MLX (Fairchild Semiconductor)TXRX USB2.0 HS OTG ULPI 32MLP PDF资料下载
参数资料
| 型号： | FUSB2805MLX |
| 厂商： | Fairchild Semiconductor |
| 文件页数： | 23/49页 |
| 文件大小： | 0K |
| 描述： | TXRX USB2.0 HS OTG ULPI 32MLP |
| 标准包装： | 1 |
| 系列： | * |
| 其它名称： | FUSB2805MLXFSDKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页
2008 Fairchild Semiconductor Corporation
www.fairchildsemi.com
FUSB2805 Rev. 1.0.3
3
F
USB2
8
0
5
—
USB2
.0
High
-S
pee
d
OTG
Tra
nsc
e
iv
e
rw
ith
UL
P
I
Inter
fac
e
Pin Definitions
Symbol
Type
Description
Chip Select_N
I
Active LOW. HIGH
– ULPI pin three-stated; LOW – ULPI operates normally. TTL
compatible; CMOS input with hysteresis.
RREF
AI/O
Resistor reference. Connect through 12 k
1% to GND.
DM
AI/O
USB D- pin. USB mode: data minus (D-) pin of the USB cable.
DP
AI/O
USB D+ pin. USB mode: data plus (D+) pin of the USB cable.
FAULT
I
FAULT is used to signal a VBUS over-current/over-voltage condition from an external
SMPS or power management IC. The link must enable this function via the
ExternalVbusFault register bit and the polarity must be set via the
ExternalVbusActiveLow register bit.
ID
I
Identification (ID) pin of the micro-USB cable. TTL; if not used, connect to 3V3.
VCC
P
Input supply voltage or battery source.
PSW
O
Controls an external, active HIGH,
VBUS power switch/charge pump and/or an SMPS
charger IC. An external 100 k
pull-down resistor is required. Open source, slew-rate-
controlled output; this pin is referenced to VCC3V3.
VBUS
AI/O
Should be connected to the VBUS pin of the USB cable. Leave open circuit if not used.
An internal 90 k
±11% pull-down resistor is present on this pin.
VCC3V3
P
3.3 V regulator output requiring capacitors. Internally powers OTG, analog core, and
ATX.
CLKIN
I
Clock input; frequency depends on the CFG1 pin. This is a digital input buffer, not
analog for a crystal.
I.C.
I/O
Internally connected; float pin.
TEST
I/O
Internally connected; float pin.
CFG1
I
Configures the clock frequency; 0: input is 19.2 MHz. 1: input is 26 MHz.
VDD1V2
P
1.2 V regulator output requiring capacitors. Internally powers the digital core and
analog core.
VIO
P
Input I/O supply rail; 0.1 F capacitor connected to power input.
Reset_N
I
Connect to VIO when not used. Resets the transceiver; active LOW.
GND
P
Connect to ground.
DIR
O
ULPI direction output signal.
STP
I
ULPI stop input signal; CMOS input.
NXT
O
ULPI next output signal.
D7
I/O
ULPI data pin 7; three-state output.
D6
I/O
ULPI data pin 6; three-state output.
D5
I/O
ULPI data pin 5; three-state output.
D4
I/O
ULPI data pin 4; three-state output.
D3
I/O
ULPI data pin 3; three-state output.
D2
I/O
ULPI data pin 2; three-state output.
D1
I/O
ULPI data pin 1; three-state output.
D0
I/O
ULPI data pin 0; three-state output.
CLOCK
O
60 MHz clock output when digital 19.2 MHz (or 26 MHz) clock is applied; Push-pull
output.
Notes:
1.
I=input; O=output; I/O=digital input/output; OD=open-drain output; AI/O=analog input/output; P=power or ground.
2.
Per USB2.0, below a supply of 2.97 V, USB full-speed and low-speed transactions are not guaranteed; although
some devices may continue to function with the FUSB2805 at the lower supply rail.
相关PDF资料 |
PDF描述 |
|---|---|
| FXLA2203UMX | TRANSLATOR LEVEL DUAL 24UMLP |
| GAL16V8D-15LJN | SPLD 62.5MHZ EECMOS 20 PLCC |
| GAL18V10B-20LP | IC GAL 10OUT MACROCELL 7.5NS 20 |
| GAL22V10D-25LJ | IC SPLD 3.3V 28-PLCC |
| GH65C11-C-PD | OPTO ENCODER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FUSCA REF BOARD | 制造商:TDK 功能描述:REFERENCE BOARD FUSCA 2.4GHZ |
| FUSCAREFBOARD | 制造商:Antenova 功能描述:Reference Board Fusca 2.4GHz |
| FUSE | 功能描述:保险丝 Fuse, Fiber 20A 600V Lot Qty 5 RoHS:否 制造商:Littelfuse 产品:Surface Mount Fuses 电流额定值:0.5 A 电压额定值:600 V 保险丝类型:Fast Acting 保险丝大小/组:Nano 尺寸:12.1 mm L x 4.5 mm W 安装风格: 端接类型:SMD/SMT 系列:485 |
| FUSE 25A ATC | 制造商:American Technical Ceramics Corp 功能描述: 制造商:ATC 功能描述: |
| FUSE KIT D | 制造商:COOPER BUSSMANN 功能描述:BUSSMANN FUSE KIT |
发布紧急采购，3分钟左右您将得到回复。