- 您现在的位置：买卖IC网 > PDF目录385377 > HGTG20N120E2 (HARRIS SEMICONDUCTOR) 34A, 1200V N-Channel IGBT PDF资料下载
参数资料
| 型号： | HGTG20N120E2 |
| 厂商： | HARRIS SEMICONDUCTOR |
| 元件分类： | 功率晶体管 |
| 英文描述： | 34A, 1200V N-Channel IGBT |
| 中文描述： | 34 A, 1200 V, N-CHANNEL IGBT, TO-247 |
| 文件页数： | 5/5页 |
| 文件大小： | 167K |
| 代理商： | HGTG20N120E2 |
3-102
HGTG20N120E2
Handling Precautions for IGBTs
Insulated Gate Bipolar Transistors are susceptible to gate-
insulation damage by the electrostatic discharge of energy
through the devices. When handling these devices, care
should be exercised to assure that the static charge built in
the handler’s body capacitance is not discharged through
the device. With proper handling and application procedures,
however, IGBTs are currently being extensively used in
production by numerous equipment manufacturers in
military, industrial and consumer applications, with virtually
no damage problems due to electrostatic discharge. IGBTs
can be handled safely if the following basic precautions are
taken:
1. Prior to assembly into a circuit, all leads should be kept
shorted together either by the use of metal shorting
springs or by the insertion into conductive material such
as “
ECCOSORBD LD26” or equivalent.
2. When devices are removed by hand from their carriers,
the hand being used should be grounded by any suitable
means - for example, with a metallic wristband.
3. Tips of soldering irons should be grounded.
4. Devices should never be inserted into or removed from
circuits with power on.
5.
Gate Voltage Rating
- Never exceed the gate-voltage
rating of VGEM. Exceeding the rated VGE can result in
permanent damage to the oxide layer in the gate region.
6.
Gate Termination
- The gates of these devices are
essentially capacitors. Circuits that leave the gate open-
circuited or floating should be avoided. These conditions
can result in turn-on of the device due to voltage buildup
on the input capacitor due to leakage currents or pickup.
7.
Gate Protection
- These devices do not have an internal
monolithic zener diode from gate to emitter. If gate
protection is required an external zener is recommended.
Trademark Emerson and Cumming, Inc.
Operating Frequency Information
Operating frequency information for a typical device (Figure
10) is presented as a guide for estimating device performance
for a specific application. Other typical frequency vs collector
current (I
CE
) plots are possible using the information shown
for a typical unit in Figures 7, 8 and 9. The operating
frequency plot (Figure 10) of a typical device shows f
MAX1
or
f
MAX2
whichever is smaller at each point. The information is
based on measurements of a typical device and is bounded
by the maximum rated junction temperature.
f
MAX1
is defined by f
MAX1
= 0.05/t
D(OFF)I
. t
D(OFF)I
deadtime
(the denominator) has been arbitrarily held to 10% of the on-
state time for a 50% duty factor. Other definitions are
possible. t
D(OFF)I
is defined as the time between the 90%
point of the trailing edge of the input pulse and the point
where the collector current falls to 90% of its maximum
value. Device turn-off delay can establish an additional fre-
quency limiting condition for an application other than T
JMAX
.
t
D(OFF)I
is important when controlling output ripple under a
lightly loaded condition. f
MAX2
is defined by f
MAX2
= (Pd - Pc)/
W
OFF
. The allowable dissipation (Pd) is defined by Pd =
(T
JMAX
- T
C
)/R
θ
JC
. The sum of device switching and conduc-
tion losses must not exceed Pd. A 50% duty factor was used
(Figure 10) and the conduction losses (Pc) are approximated
by Pc = (V
CE
I
CE
)/2. W
OFF
is defined as the integral of the
instantaneous power loss starting at the trailing edge of the
input pulse and ending at the point where the collector
current equals zero (I
CE
= 0A).
The switching power loss (Figure 10) is defined as f
MAX2
W
OFF
. Turn-on switching losses are not included because
they can be greatly influenced by external circuit conditions
and components.
Test Circuit
FIGURE 12. INDUCTIVE SWITCHING TEST CIRCUIT
20V
0V
R
GEN
= 50
1/R
G
= 1/R
GEN
+ 1/R
GE
R
GE
= 50
L = 50
μ
H
V
960V
+
-
相关PDF资料 |
PDF描述 |
|---|---|
| HGTG20N120 | 34A, 1200V N-Channel IGBT |
| HGTG20N50C1D | 36 MACROCELL 3.3 VOLT ISP CPLD |
| HGTG20N60B3D | 40A, 600V, UFS Series N-Channel IGBT with Anti-Parallel Hyperfast Diode(40A, 600V，N沟道绝缘栅双极晶体管（带反并行超快速二极管)) |
| HGTG24N60D1D | 3.3V 36-mc CPLD |
| HGTG24N60D1 | 36 MACROCELL 3.3 VOLT ISP CPLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HGTG20N50C1D | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HGTG20N60A4 | 功能描述:IGBT 晶体管 600V N-Channel IGBT SMPS Series RoHS:否 制造商:Fairchild Semiconductor 配置: 集电极—发射极最大电压 VCEO:650 V 集电极—射极饱和电压:2.3 V 栅极/发射极最大电压:20 V 在25 C的连续集电极电流:150 A 栅极—射极漏泄电流:400 nA 功率耗散:187 W 最大工作温度: 封装 / 箱体:TO-247 封装:Tube |
| HGTG20N60A4 | 制造商:Fairchild Semiconductor Corporation 功能描述:IGBT N TO-247 |
| HGTG20N60A4_NL | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| HGTG20N60A4D | 功能描述:IGBT 晶体管 600V RoHS:否 制造商:Fairchild Semiconductor 配置: 集电极—发射极最大电压 VCEO:650 V 集电极—射极饱和电压:2.3 V 栅极/发射极最大电压:20 V 在25 C的连续集电极电流:150 A 栅极—射极漏泄电流:400 nA 功率耗散:187 W 最大工作温度: 封装 / 箱体:TO-247 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。