参数资料
| 型号： | HIP1012EVAL1 |
| 厂商： | Intersil |
| 文件页数： | 13/15页 |
| 文件大小： | 0K |
| 描述： | EVALUATION BOARD DUAL GENERIC |
| 标准包装： | 1 |
| 主要目的： | 电源管理，热交换控制器 |
| 已用 IC / 零件： | HIP1012 |
| 已供物品： | 板 |
HIP1012A
HIP1012 Evaluation Circuit for Disk Drive Hot Swap HIP1012EVAL2
Introduction
The HIP1012EVAL2 is specifically designed to test and
demonstrate hot swapping of disk drives onto passive 12V
and 5V power buses using the HIP1012 Hot-Swap control
IC. The small size of the board allows it to be included in a
shuttle alongside the disk drive during evaluation. The
outlined area on the board represents the actual area used
for PCB implementation.
Description
The HIP1012EVAL2 board is provided with a standard Molex
four-terminal disk-drive power connector. The solder holes
J2 allows the board to be connected to a power supply
connector on the disk-drive shuttle. PGOOD, PWRON1,
PWRON2, 5VG. 12VG, CTIM, V DD and GND are all
accessible through a ribbon cable.
With JP1 installed, the HIP1012 is powered from the same
12V power supply as the disk drive motor. JP2 connects the
control signal PWRON2 to ground allowing the unit to be
plugged directly into the power bus for automatic, controlled
startup. In this configuration, PWRON1 is available to reset
the HIP1012 in case of an over-current trip. Otherwise the
HIP1012 can be reset by toggling the voltage on V DD . With
JP2 removed, the circuit is controlled using one or both of
the PWRON signal lines. The HIP1012EVAL2 is shipped
with both jumpers installed.
The HIP1012EVAl2 is configured with a 10k ? RILIM
resistor (R 5 ) setting the nominal current limit threshold to
100mV. The 12V current sense resistor (R 2 ) is 20m ? and
the 5V current sense resistor (R 1 ) is 100m ?. These values
set the nominal current limits to 5A and 1A respectively.
The C TIM capacitor (C 2 ) sets the time out period to
approximately 9ms.
13
Control Connections, Fault Notification, and Test
Points
HIP1012 EVAL2 is shipped with JP2 installed so that a
connected disk drive is started simply by connecting 12V
and 5V power supplies to J2. In this configuration, the
ribbon cable is not necessary, since the HIP1012 can be
reset by toggling the voltage on V DD . This configuration
represents a disk drive that would be removed after any
over-current trip and would start immediately upon
insertion. Additional control is available using the ribbon
cable and resetting the HIP1012 by applying a rising edge
to PWRON1. If redundant control is desired, removing JP2
makes the second control signal PWRON2 available to
start or reset the chip. An example of this control
configuration would be to turn the chip on using PWRON1
and reset it using PWRON2. The PGOOD pin is an open
drain logic output which can be tied high through a resistor
for fault indication. Upon detection of either overcurrent or
undervoltage fault conditions, PGOOD goes low and
remains low until the fault condition is cleared.
Also included on the ribbon cable are additional monitor
points for 12VG, 5VG and C TIM . These are included for
monitoring during evaluation and they are not necessary
for operation.
Data Line Considerations
The HIP1012A does not integrate data bus line switches,
although control of the data bus can be assisted by the time-
out feature of the HIP1012A. During the time-out period, the
operating system software can determine whether to halt I/O
activity to a disk drive which is undergoing an under-voltage
or over-current fault as indicated by the status of PGOOD.
相关PDF资料 |
PDF描述 |
|---|---|
| HIP1013EVAL1 | EVALUATION BOARD DUAL GENERIC |
| HIP2100EVAL2 | EVAL BOARD 48VDC-5UDC CONVERTER |
| HIP2100EVAL | EVAL BOARD MINI HALF BRIDGE |
| HIP4080AEVAL | EVALUATION BOARD HIP4080/4081 |
| HIP4082EVAL | EVAL BOARD FET DRIVER HIP4082 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HIP1012EVAL2 | 功能描述:电源管理IC开发工具 RAID EVALUATION BRD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| HIP1013 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Low Cost Dual Power Distribution Controller |
| HIP1013_04 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Low Cost Dual Power Distribution Controller |
| HIP1013CB | 功能描述:IC CTRLR HOTPLUG DUAL 14-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| HIP1013CB-T | 功能描述:IC CTRLR HOTPLUG DUAL 14-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。